Grizzly G1022SM instruction manual Miter Gauge, Initial Step Models ZF, ZFX, PROZ, & Prozx

Page 36

Miter Gauge

Initial Step Models ZF, ZFX, PROZ, & PROZX:

The miter gauge for the Models ZF, ZFX, PROZ,

&PROZX has two setscrews in the miter bar which can be set to remove any loose movement between the miter bar and the T-slot.

Loosen or tighten the two setscrews until the miter gauge slides freely in the slot, but has no loose movement.

Next steps for all models:

1.Loosen the lock knob on the miter gauge and place a square against the face of the miter body and the miter bar.

2.Adjust the miter body until there is no space between the square and the miter bar.

3.Tighten the lock knob.

4.With the stop link (Figure 43) in the up posi- tion, loosen the jam nut and adjust the stop screw until it is seated against the stop link.

5.Loosen the setscrew on the left front side of the miter bar, adjust the pointer to 90û and retighten the setscrew.

6.To adjust to 45û, follow Steps 1-5while using an adjustable square.

7.After rotating the miter body from 45û to 90û and back a few times, double check your adjustments at both angles to ensure that you have accurately set your miter gauge.

Stop Link

Jam Nut

Stop Screw

Figure 43. Miter gauge adjustment points.

-34-	G1022 Series Contractor Saws

Image 36

Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksZero Clearance Table Inserts Push PaddlesFeatherboards Introduction CommentaryG1022 Series Table Saws Circuit Requirements 110V OperationModels SM & Z Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyHandwheels All ModelsTo mount the handwheels Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings To install and adjust the Model SM fence Fence RailsFence To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertMiter Gauge Initial Step Models ZF, ZFX, PROZ, & ProzxNext steps for all models Start Up Recommended Adjustments Recommended adjustment checklistStarting the machine Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralLubrication BeltLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog