Grizzly G1022SM instruction manual Various saw tooth cutting profiles G1022 Series Table Saws

Page 39

Plywood Blade: Used for cutting plywood or veneers. 10" plywood blades have 40-80 teeth (Figure 47), a steep alternate top bevel tooth pro- file (Figure 49) and very shallow gullet.

Figure 47. Plywood blade.

Thin-kerf:Designed for saws with smaller motors and for reducing material waste, thin-kerf blades are thinner than standard blades. Performance and accuracy can be maintained by the use of blade stabilizers.

Some blade guards/splitters are thicker than thin-kerf blades. DO NOT use the thin- kerf blade if this is the case or serious per- sonal injury could result.

Dado Blades: There are two types of dado

blades: stacked and wobble.

¥Stacked Dado BladeÑThese dedicated dado cutting blades consist of a set of up to 8 indi- vidual blades. Multiple cutters are "stacked" between two outside blades. The width of the dado is determined by the combination of cut- ters that are ÒstackedÓ together. The dado is cut in a single pass leaving a smooth and square channel in the face of the workpiece as shown on Page 40. Stacked dado blades are the most expensive option but are worth considering if your projects require a lot of visible dado cuts. A typical stacked dado blade is shown in Figure 48.

Figure 48. Optional dado blade.

¥Wobble Dado BladeÑAlso a dedicated dado blade, a wobble blade usually consists of a sin- gle blade that is tilted on the arbor shaft while it is spinning. The channel is cut in the face of the workpiece as the blade passes through its pre- adjusted width of travel. Wobble blades are an inexpensive option when visibly pleasing chan- nels are not a concern.

Moulding Heads: A moulding head is a cutter- head that attaches to the arbor and holds individ- ual moulding knives. They should only be used by professional woodworkers with training beyond the scope of this manual.

This section on blade selection is by no means comprehensive. Always follow the saw blade manufacturer's recommendations to ensure safe and efficient operation of your table saw.

Figure 49. Various saw tooth cutting profiles.

G1022 Series Table Saws

-37-

Image 39

Contents G1022ZFX G1022SM G1022Z G1022ZFPage Table Of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesZero Clearance Table Inserts Push PaddlesFeatherboards Commentary IntroductionG1022 Series Table Saws Model ZF Circuit Requirements110V Operation Models SM & ZModels ZFX, PROZ, & Prozx 220V OperationExtension Cord GroundingTerms and Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPMotor with Pulley Hardware Contents Bolt Hardware Recognition ChartWorking Clearance Clean UpSite Considerations Floor LoadBeginning Assembly Stand Assembly Models ZF, ZFX, PRO, & Prozx only Stand completely assembledHandwheels All ModelsTo mount the handwheels Motor Checking V-belt alignment Models ZF, ZFX, PROZ, & Prozx SwitchExtension Wings To mount the rails Models SM & Z To install and adjust the Model SM fenceFence Rails FenceAdjust measurement pointer G1022 Series Table Saws Attaching a sacrificial fence To install and adjust the Model Z fenceAttaching a sacrificial fence G1022 Series Table Saws Changing saw blade G1022 Series Table Saws BladeBlade Guard Installing blade guardProper Alignment Added Washers Table Insert Adjusting table insert components G1022 Series Table SawsMiter Gauge Initial Step Models ZF, ZFX, PROZ, & ProzxNext steps for all models Start Up Recommended Adjustments Recommended adjustment checklistStarting the machine Blade Selection OperationsVarious saw tooth cutting profiles G1022 Series Table Saws Cross-cut operation G1022 Series Table Saws CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1022 Series Table Saws Rabbet CuttingCutting rabbets with the dado blade Disconnect the machine from the powerCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws General MaintenanceLubrication BeltLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Blade Parallelism Service AdjustmentsTo shift the trunnion Shim placement G1022 Series Table SawsTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog