Grizzly G1022SM instruction manual Safety Instructions For Power Tools

Page 4

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

								Indicates an imminently hazardous situation which, if not avoided,
								WILL result in death or serious injury.
								Indicates a potentially hazardous situation which, if not avoided,


								COULD result in death or serious injury.
								COULD result in death or serious injury.
								Indicates a potentially hazardous situation which, if not avoided,

								MAY result in minor or moderate injury, or MAY cause property
								damage.



	NOTICE							This symbol is used to alert the user to useful information about
	NOTICE							proper operation of the equipment.

Safety Instructions For Power Tools

1.KEEP GUARDS IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.DO NOT USE IN DANGEROUS ENVI- RONMENT. Do not use power tools in damp or wet locations, or where any flam- mable or noxious fumes may exist. Keep work area well lighted.

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area.

6.MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.

7.DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

-2-	G1022 Series Table Saws

Image 4

Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksPush Paddles Zero Clearance Table InsertsFeatherboards Introduction CommentaryG1022 Series Table Saws Circuit Requirements 110V OperationModels SM & Z Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyAll Models HandwheelsTo mount the handwheels Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings To install and adjust the Model SM fence Fence RailsFence To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertInitial Step Models ZF, ZFX, PROZ, & Prozx Miter GaugeNext steps for all models Recommended adjustment checklist Start Up Recommended AdjustmentsStarting the machine Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralBelt LubricationLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog