Grizzly G1012 instruction manual Hardware Bags, Inside Bags Qty

Page 11

Figure 3. Stand components.

Figure 4. Bandsaw components.

Hardware Bags

Inside Bags

Qty

Carriage Bolts 5⁄16" - 18 x 1⁄2"

24

Flat Washers 5⁄16"

40

Nuts 5⁄16" - 18

32

Hex Head Bolts 5⁄16" - 18 x 3⁄4"

4

Hex Head Bolts 5⁄16"-18 x 1"

4

Hex Head Bolts 1⁄2" - 12 x 11⁄2"

4

Hex Nuts 1⁄2" - 12

4

Flat Washers 1⁄2"

8

Cap Screws 1⁄4"-20 x 11⁄2"

4

Phillip Hd Screws 1⁄4" - 20 x 1⁄2"

2

Hex Nuts 1⁄4" - 20

2

Flat Washers 1⁄4"

4

Setscrews 1⁄4" x 1⁄4"

2

Hex Bolts 3⁄8"-16 x 3⁄4"

2

Hex Bolts 3⁄8"-16 x 11⁄4"

2

Hex Nuts 3⁄8"-16

5

Flat Washers 3⁄8"

4

Lock Nuts 3⁄8"

4

Hex Bolt 3⁄8"-16 x 3"

1

Hex Bolt 5⁄8"-11

2

Flat Washers 5⁄8"

2

Fence Rail Spacers

4

5 x 5 x 20mm Key

1

Lock Knob (Male)

1

Star Knobs (Female)

2

Strain Relief w/Plastic Nut 1⁄2"

1

5mm Hex Wrench

1

3mm Hex Wrench

1

Adjustment Bolts (w/Eye)

2

Guide Blocks

8

Thumbscrews 1⁄4"-20 x 1⁄2"

8

Roll Pin 3 x 10mm

1

Table Insert

1

Rubber Feet

4

In the event that any non-proprietary parts are missing (e.g. nuts or washers), we would be glad to replace them, or for the sake of expediency, replacements can be obtained at your local hard- ware store.

G1012 18" Bandsaw

-9-

Page 10 Page 12
Image 11
Page 10 Page 12
Contents HEAVY-DUTY Bandsaw Page Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Additional Safety Instructions For Bandsaws Circuit Requirements 220V Operation FusingGrounding Extension Cords Commentary General InformationSee Figure Unpacking Piece InventoryInside Bags Qty Hardware BagsHardware Recognition Chart Site Considerations Clean upStand AssemblyOrder of Assembly Legs, braces, and one stand side Attached to stand Bandsaw unit mounted to stand Pulleys Belts Belts mounted on pulleys Belt GuardTo mount the table to the bandsaw unit Fence To install the upper and lower blade guidesBlade Guides Controls AdjustmentsBlade Tension To adjust the tensionBlade Tracking To set the guide-blocks within the guide- block holder To adjust guide assembly alignment on guide postGuide Post Lower Blade Guide Assemblies Blade Changes Table AdjustmentsSquaring table to blade back G1012 18 Bandsaw To adjust the miter slot parallel to the band- saw bladeTo skew your fence Fence Adjustment Blade LeadTo verify if the the upper and lower wheels are coplanar Wheel AlignmentShimming a wheel Coplanar diagram G1012 18 BandsawOverview OperationsTest Run Tooth Style Blade InformationBlade Length Blade WidthBlade Breakage Tooth PitchBlade Care To crosscut with the Model G1012 RippingCrosscutting To rip with the Model G1012Crosscutting with miter gauge ResawingTo complete a stacked cut Cutting CurvesStacked Cuts Lubrication MaintenanceMiscellaneous G1012 18 Bandsaw Closure Machine Data Sheet G1012 18 Bandsaw G1012 18 Bandsaw G1012 18 Bandsaw G1012 18 Bandsaw Upper Frame ARM Switch Troubleshooting Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC
Top Page Image Contents