Grizzly G1012 instruction manual Order of Assembly, Stand

Page 14

SECTION 4: ASSEMBLY

Keep loose clothing out of the way of machinery and keep hair pulled back, or serious injury may occur.

Disconnect power to the machine when perform- ing any maintenance or assembly. Failure to do this may result in serious personal injury.

Wear safety glasses dur- ing the entire assembly process. Failure to com- ply may result in serious personal injury.

Order of Assembly

We have organized the assembly process of the Model G1012 into steps listed below. Please fol- low them in sequence. The inventory photos and lists, hardware recognition chart, parts list and exploded diagram have been provided to make assembly as easy as possible.

1.Stand

2.Motor

3.Mounting Unit to Stand

4.Wiring

5.Pulley Alignment

6.Table

7.Fence Assembly

8.Total Unit Check

NOTICE

TOOLS REQUIRED: In addition to the tools provided with your bandsaw, you will need a metric set of wrenches, large and medium flat-tipped screwdrivers, a Phillips® screw- driver, and a 6" or 8" adjustable wrench.

Stand

To begin the stand assembly, locate all the stand parts so they are within easy reach.

1.Flip the stand top upside down. Install the two adjustment bolts on the stand top by placing the 3⁄8"-16 x 11⁄4" carriage bolts through the mounts on the stand top and then the through eyes of the adjustment bolts. Secure with 3⁄8" washers and hex nuts, but do not completely tighten.

2.Using (2) 3⁄8"-16 x 3⁄4" carriage bolts, wash- ers, and hex nuts; attach the motor bracket to the mounts on the stand top without tight- ening.

3.Place a 3⁄8"-16 hex nut and washer on each adjustment bolt, then rotate the motor brack- et over the adjustment bolts, and secure with another 3⁄8"-16 hex nut and washer so your assembly looks like Figure 5. Again, do not completely tighten at this time.

-12-

G1012 18" Bandsaw

Page 13 Page 15
Image 14
Page 13 Page 15
Contents HEAVY-DUTY Bandsaw Page Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For Bandsaws 220V Operation Fusing Circuit RequirementsGrounding Extension Cords General Information CommentaryUnpacking Piece Inventory See FigureHardware Bags Inside Bags QtyHardware Recognition Chart Clean up Site ConsiderationsStand AssemblyOrder of Assembly Legs, braces, and one stand side Attached to stand Bandsaw unit mounted to stand Pulleys Belts Belt Guard Belts mounted on pulleysTo mount the table to the bandsaw unit Fence To install the upper and lower blade guidesBlade Guides Adjustments ControlsBlade Tension To adjust the tensionBlade Tracking To set the guide-blocks within the guide- block holder To adjust guide assembly alignment on guide postGuide Post Lower Blade Guide Assemblies Table Adjustments Blade ChangesTo adjust the miter slot parallel to the band- saw blade Squaring table to blade back G1012 18 BandsawFence Adjustment Blade Lead To skew your fenceWheel Alignment To verify if the the upper and lower wheels are coplanarCoplanar diagram G1012 18 Bandsaw Shimming a wheelOverview OperationsTest Run Blade Width Blade InformationBlade Length Tooth StyleBlade Breakage Tooth PitchBlade Care To rip with the Model G1012 RippingCrosscutting To crosscut with the Model G1012Resawing Crosscutting with miter gaugeTo complete a stacked cut Cutting CurvesStacked Cuts Lubrication MaintenanceMiscellaneous G1012 18 Bandsaw Closure Machine Data Sheet G1012 18 Bandsaw G1012 18 Bandsaw G1012 18 Bandsaw G1012 18 Bandsaw Upper Frame ARM Switch Troubleshooting Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA
Top Page Image Contents