Grizzly G0457 owner manual Safety Instructions for Machinery

Page 8

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

WILL result in death or serious injury.

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

COULd result in death or serious injury.

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this owner’s manual BEFORE using machine. Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses.

HAzARdOUS dUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk.

WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips which could cause a loss of work- piece control.

HEARING PROTECTION. Always wear hear- ing protection when operating or observiing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

-6-

G0457 14" Industrial Bandsaw (Mfg. Since 5/11)

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model G0457 Industrial Bandsaw Page Table of Contents Introduction Manual Accuracy Contact InfoIdentification Machine Data Sheet Cutting Capacities Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Additional Safety Instructions for Bandsaws Power Supply AvailabilityFull-Load Current Rating Circuit InformationGrounding Requirements Typical 5-20 plug and receptacleVoltage Conversion Disabling & Locking SwitchExtension Cords Setup Needed for SetupUnpacking Description QtyHardware Recognition Chart Hardware Not shown Contents Figures QtyInventory Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the bandsawTable installed on trunnions Installed front rail Dust Collection To connect a dust collection hoseChanges in the blade tension may change the blade tracking Blade TrackingTo center track the blade Test Run Table Stop CalibrationTo test run the machine Blade Tracking onTable Alignment To calibrate the pointer on the table tilt scaleTo align the fence parallel with the miter slot Fence AlignmentTo calibrate the miter gauge Adjusting Support Bearings To adjust the support bearingsBlade Tensioning To tension the bandsaw bladeTop View Blade Guide Adjustments To adjust the upper and lower blade guidesOperations Basic ControlsOverview Straight CutsIrregular Cuts Basic Cutting TipsTo tilt the table Workpiece InspectionTable Tilt To rip with the Model G0457 To adjust guide postGuide Post Ripping CrosscuttingResawing To crosscut with the Model G0457Cutting Curves To resaw a workpieceStacked Cuts To complete a stacked cutBlade Information Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areTo replace the blade Blade ChangesTo remove the blade Accessories Half-mask respirator with disposable Cartridge filters H5408-Blade Tensioning GaugeG1928-Bandsaw Handbook G8983-Tilting Roller StandG8984-Single Roller Stand G8985-5 Roller StandMaintenance CleaningSchedule Unpainted Cast IronGuide Post Blade Tension LeadscrewTo redress the rubber tires Redressing Rubber TiresTable Trunnions Motor & Electrical ServiceTroubleshooting Adjust the feet on the bottom of the stand relocate Checking V-Belt Tensioning V-BeltTo check the V-belt Steps Tools Needed QtyReplacing V-Belt To replace the V-beltShimming Table Blade Lead Correct blade leadSkewing your fence To shim the tableShifting Table To check if your wheels are coplanar Wheel AlignmentComponents and Hardware Needed Qty Coplanarity Gauge Wiring Wiring Safety Instructions110V Main Main Parts List DescriptionTrunnion Bracket Cast Iron Components DescriptionStand Labels Rear of MachineWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns Order Hours a DAY

G0457 specifications

The Grizzly G0457 is a versatile and robust woodworking tool designed to meet the needs of both amateur woodworkers and professional craftsmen. This cabinet-style bandsaw offers a blend of power, precision, and durability, making it an essential addition to any serious workshop.

One of the standout features of the G0457 is its powerful 2 HP motor, which provides ample strength to cut through a variety of materials, including hardwoods and softwoods. This motor is designed for consistent performance, minimizing the risk of stalling during operation. Furthermore, the bandsaw is equipped with a large cutting capacity, boasting a 14-inch resaw height and a 13-inch maximum cutting width, enabling users to tackle larger projects with ease.

The construction of the Grizzly G0457 is another key highlight. The machine features a solid cast iron frame that enhances stability and reduces vibrations during operation. This sturdy design contributes to improved accuracy, ensuring that cuts are clean and true. Furthermore, the oversized wheels are made of aluminum, allowing for smoother operation and a longer lifespan.

In terms of technology, the G0457 utilizes a precision-machined aluminum fence system. This system is designed for easy adjustments, providing users with the ability to make quick and accurate cuts. The bandsaw also includes a blade tension release, which simplifies blade changes and prolongs the lifespan of the blade itself. Additionally, the quick-release blade tension lever allows for easy adjustments, enhancing overall efficiency.

Safety features are also a priority in the design of the Grizzly G0457. It includes an easy-to-access power switch and a blade guard to protect users from potential injuries. The adjustable upper and lower blade guides ensure optimal performance and safety during operation.

The G0457 is also designed with convenience in mind. It includes a built-in dust port to help maintain a clean workspace. This feature minimizes dust accumulation, promoting a healthier environment and improving visibility while cutting.

In summary, the Grizzly G0457 bandsaw is a powerful and reliable tool that combines innovative features, robust construction, and user-friendly design. Whether you are ripping boards, resawing, or making intricate cuts, the G0457 stands out as a reliable choice for anyone serious about woodworking. Its attention to detail, performance capabilities, and safety features make it an invaluable asset in any workshop.
Top Page Image Contents