Grizzly G0457 owner manual Unattended OPERATION. Never­ leave­

Page 9

­

DISCONNECTING POWER SUPPLY.­Always­dis- connect­ machine­ from­ power­ supply­ before­ ser- vicing,­ adjusting,­ or­ changing­ cutting­ tools­ (bits,­ blades,­ cutters,­ etc.).­ Make­ sure­ switch­ is­ in­ OFF­ position­before­reconnecting­to­avoid­an­unexpect- ed­or­unintentional­start.

APPROVED OPERATION.­ Untrained­ operators­ can­ be­ seriously­ hurt­ by­ machinery.­ Only­ allow­ trained­ or­ properly­ supervised­ people­ to­ use­ machine.­ When­ machine­ is­ not­ being­ used,­ dis- connect­ power,­ remove­ switch­ keys,­ or­ lock-out­ machine­to­prevent­unauthorized­use—especially­ around­children.­Make­workshop­kid­proof!

DANGEROUS ENVIRONMENTS. Do­ not­ use­ machinery­ in­ wet­ or­ rainy­ locations,­ cluttered­ areas,­ around­ flammables,­ or­ in­ poorly-lit­ areas.­ Keep­ work­ area­ clean,­ dry,­ and­ well-lighted­ to­ minimize­risk­of­injury.

ONLY USE AS INTENDED.­ Only­ use­ machine­ for­ its­ intended­ purpose.­ Never­ modify­ or­ alter­ machine­for­a­purpose­not­intended­by­the­manu- facturer­or­serious­injury­may­result!

USE RECOMMENDED ACCESSORIES.­Consult­ this­owner’s­manual­or­the­manufacturer­for­rec- ommended­ accessories.­ Using­ improper­ acces- sories­will­increase­the­risk­of­serious­injury.

CHILDREN & BYSTANDERS. Keep­ children­ and­bystanders­a­safe­distance­away­from­work­ area.­Stop­using­machine­if­children­or­bystand- ers­become­a­distraction.

REMOVE ADJUSTING TOOLS.­ Never­ leave­ adjustment­tools,­chuck­keys,­wrenches,­etc.­in­or­ on­machine—especially­near­moving­parts.­Verify­ removal­before­starting!

SECURING WORKPIECE.­ When­ required,­ use­ clamps­ or­ vises­ to­ secure­ workpiece.­ A­ secured­ workpiece­protects­hands­and­frees­both­of­them­ to­operate­the­machine.

FEED DIRECTION.­Unless­otherwise­noted,­feed­ work­ against­ the­ rotation­ of­ blades­ or­ cutters.­ Feeding­in­the­same­direction­of­rotation­may­pull­ your­hand­into­the­cut.

FORCING MACHINERY.­Do­not­force­machine.­ It­ will­ do­ the­ job­ safer­ and­ better­ at­ the­ rate­ for­ which­it­was­designed.

GUARDS & COVERS.­ Guards­ and­ covers­ can­ protect­ you­ from­ accidental­ contact­ with­ moving­ parts­ or­ flying­ debris.­ Make­ sure­ they­ are­ prop- erly­installed,­undamaged,­and­ working­ correctly­ before­using­machine.

NEVER STAND ON MACHINE.­Serious­injury­or­ accidental­ contact­ with­ cutting­ tool­ may­ occur­ if­ machine­is­tipped.­Machine­may­be­damaged.

STABLE MACHINE. Unexpected­movement­dur- ing­operations­greatly­increases­the­risk­of­injury­ and­ loss­ of­ control.­ Verify­ machines­ are­ stable/ secure­ and­ mobile­ bases­ (if­ used)­ are­ locked­ before­starting.

AWKWARD POSITIONS.­ Keep­ proper­ footing­ and­balance­at­all­times­when­operating­machine.­ Do­not­overreach!­Avoid­awkward­hand­positions­ that­ make­ workpiece­ control­ difficult­ or­ increase­ the­risk­of­accidental­injury.

UNATTENDED OPERATION. Never­ leave­

machine­running­while­unattended.­Turn­machine­ off­and­ensure­all­moving­parts­completely­stop­ before­walking­away.

MAINTAIN WITH CARE.­Follow­all­maintenance­ instructions­ and­ lubrication­ schedules­ to­ keep­ machine­in­good­working­condition.­An­improperly­ maintained­machine­may­increase­the­risk­of­seri- ous­injury.­

CHECK DAMAGED PARTS.­ Regularly­ inspect­ machine­ for­ damaged­ parts,­ loose­ bolts,­ mis- adjusted­ or­ mis-aligned­ parts,­ binding,­ or­ any­ other­ conditions­ that­ may­ affect­ safe­ operation.­ Always­repair­or­replace­damaged­or­mis-adjust- ed­parts­before­operating­machine.

EXPERIENCING DIFFICULTIES. If­ at­ any­ time­ you­ are­ experiencing­ difficulties­ performing­ the­ intended­ operation,­ stop­ using­ the­ machine!­ Contact­ our­ Technical­ Support­ Department­ at­ (570)­546-9663.

G0457 14" Industrial Bandsaw (Mfg. Since 5/11)

-7-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model G0457 Industrial Bandsaw Page Table of Contents Manual Accuracy Contact Info IntroductionIdentification Machine Data Sheet Cutting Capacities Safety Instructions for Machinery SafetyUnattended OPERATION. Never­ leave­ Additional Safety Instructions for Bandsaws Availability Power SupplyFull-Load Current Rating Circuit InformationTypical 5-20 plug and receptacle Grounding RequirementsDisabling & Locking Switch Extension CordsVoltage Conversion Needed for Setup SetupUnpacking Description QtyHardware Recognition Chart Contents Figures Qty InventoryHardware Not shown Placement Location Clean UpSite Considerations Floor LoadTo assemble the bandsaw AssemblyTable installed on trunnions Installed front rail To connect a dust collection hose Dust CollectionBlade Tracking To center track the bladeChanges in the blade tension may change the blade tracking Table Stop Calibration Test RunTo test run the machine Blade Tracking onTo calibrate the pointer on the table tilt scale Table AlignmentFence Alignment To calibrate the miter gaugeTo align the fence parallel with the miter slot To adjust the support bearings Adjusting Support BearingsBlade Tensioning To tension the bandsaw bladeTop View To adjust the upper and lower blade guides Blade Guide AdjustmentsBasic Controls OperationsStraight Cuts OverviewIrregular Cuts Basic Cutting TipsWorkpiece Inspection Table TiltTo tilt the table To adjust guide post Guide Post RippingTo rip with the Model G0457 To crosscut with the Model G0457 CrosscuttingResawingTo resaw a workpiece Cutting CurvesTo complete a stacked cut Stacked CutsBlade Length Blade InformationBlade Width Tooth StyleBlade Care Tooth PitchBlade Breakage Most common causes of blade breakage areBlade Changes To remove the bladeTo replace the blade Accessories H5408-Blade Tensioning Gauge Half-mask respirator with disposable Cartridge filtersG8983-Tilting Roller Stand G1928-Bandsaw HandbookG8984-Single Roller Stand G8985-5 Roller StandCleaning MaintenanceSchedule Unpainted Cast IronBlade Tension Leadscrew Guide PostRedressing Rubber Tires Table TrunnionsTo redress the rubber tires Service TroubleshootingMotor & Electrical Adjust the feet on the bottom of the stand relocate Tensioning V-Belt Checking V-BeltTo check the V-belt Steps Tools Needed QtyTo replace the V-belt Replacing V-BeltCorrect blade lead Shimming Table Blade LeadSkewing your fence To shim the tableShifting Table Wheel Alignment Components and Hardware Needed QtyTo check if your wheels are coplanar Coplanarity Gauge Wiring Safety Instructions Wiring110V Main Description Main Parts ListTrunnion Bracket Cast Iron Description ComponentsStand Rear of Machine LabelsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty & Returns Order Hours a DAY

G0457 specifications

The Grizzly G0457 is a versatile and robust woodworking tool designed to meet the needs of both amateur woodworkers and professional craftsmen. This cabinet-style bandsaw offers a blend of power, precision, and durability, making it an essential addition to any serious workshop.

One of the standout features of the G0457 is its powerful 2 HP motor, which provides ample strength to cut through a variety of materials, including hardwoods and softwoods. This motor is designed for consistent performance, minimizing the risk of stalling during operation. Furthermore, the bandsaw is equipped with a large cutting capacity, boasting a 14-inch resaw height and a 13-inch maximum cutting width, enabling users to tackle larger projects with ease.

The construction of the Grizzly G0457 is another key highlight. The machine features a solid cast iron frame that enhances stability and reduces vibrations during operation. This sturdy design contributes to improved accuracy, ensuring that cuts are clean and true. Furthermore, the oversized wheels are made of aluminum, allowing for smoother operation and a longer lifespan.

In terms of technology, the G0457 utilizes a precision-machined aluminum fence system. This system is designed for easy adjustments, providing users with the ability to make quick and accurate cuts. The bandsaw also includes a blade tension release, which simplifies blade changes and prolongs the lifespan of the blade itself. Additionally, the quick-release blade tension lever allows for easy adjustments, enhancing overall efficiency.

Safety features are also a priority in the design of the Grizzly G0457. It includes an easy-to-access power switch and a blade guard to protect users from potential injuries. The adjustable upper and lower blade guides ensure optimal performance and safety during operation.

The G0457 is also designed with convenience in mind. It includes a built-in dust port to help maintain a clean workspace. This feature minimizes dust accumulation, promoting a healthier environment and improving visibility while cutting.

In summary, the Grizzly G0457 bandsaw is a powerful and reliable tool that combines innovative features, robust construction, and user-friendly design. Whether you are ripping boards, resawing, or making intricate cuts, the G0457 stands out as a reliable choice for anyone serious about woodworking. Its attention to detail, performance capabilities, and safety features make it an invaluable asset in any workshop.
Top Page Image Contents