Grizzly G0457 owner manual Installed front rail

Page 20

15.Replace the blade, and for now, only put enough tension on it to keep it on the wheels.

16.Re-install the table pin and table insert.

17.Fasten the rear rail to the back of the table with the four M6-1 x 16 cap screws, as shown in Figure 15.

Figure 15. Rear rail installed.

18.Attach the front rail to the front of the bandsaw table with the two M6-1 x 20 hex bolts, 6mm lock washers and flat washers, as shown in

Figure 16.

19.Install the handle on the fence assembly (Figure 17), and tighten the hex nut against the fence pivot block to secure the handle.

Pivot Block

Hex Nut

Figure 17. Handle installed on fence assembly.

20.Place the 8mm flat washer on the locking adjustment handle and slide it through the hole in the fence.

21.Thread the moving plate onto the end of the locking adjustment handle threads.

22.Slide the resaw fence over the moving plate, as shown in Figure 18, so the moving plate fits inside the channel of the resaw fence.

Locking

Adjustment

Handle

Moving

Plate

Figure 16. Installed front rail.

Figure 18. Attaching resaw fence to standard

 

fence.

-18-

G0457 14" Industrial Bandsaw (Mfg. Since 5/11)

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model G0457 Industrial Bandsaw Page Table of Contents Introduction Manual Accuracy Contact InfoIdentification Machine Data Sheet Cutting Capacities Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Additional Safety Instructions for Bandsaws Power Supply AvailabilityFull-Load Current Rating Circuit InformationGrounding Requirements Typical 5-20 plug and receptacleVoltage Conversion Disabling & Locking SwitchExtension Cords Setup Needed for SetupUnpacking Description QtyHardware Recognition Chart Hardware Not shown Contents Figures QtyInventory Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the bandsawTable installed on trunnions Installed front rail Dust Collection To connect a dust collection hoseChanges in the blade tension may change the blade tracking Blade TrackingTo center track the blade Test Run Table Stop CalibrationTo test run the machine Blade Tracking onTable Alignment To calibrate the pointer on the table tilt scaleTo align the fence parallel with the miter slot Fence AlignmentTo calibrate the miter gauge Adjusting Support Bearings To adjust the support bearingsBlade Tensioning To tension the bandsaw bladeTop View Blade Guide Adjustments To adjust the upper and lower blade guidesOperations Basic ControlsOverview Straight CutsIrregular Cuts Basic Cutting TipsTo tilt the table Workpiece InspectionTable Tilt To rip with the Model G0457 To adjust guide postGuide Post Ripping CrosscuttingResawing To crosscut with the Model G0457Cutting Curves To resaw a workpieceStacked Cuts To complete a stacked cutBlade Information Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areTo replace the blade Blade ChangesTo remove the blade Accessories Half-mask respirator with disposable Cartridge filters H5408-Blade Tensioning GaugeG1928-Bandsaw Handbook G8983-Tilting Roller StandG8984-Single Roller Stand G8985-5 Roller StandMaintenance CleaningSchedule Unpainted Cast IronGuide Post Blade Tension LeadscrewTo redress the rubber tires Redressing Rubber TiresTable Trunnions Motor & Electrical ServiceTroubleshooting Adjust the feet on the bottom of the stand relocate Checking V-Belt Tensioning V-BeltTo check the V-belt Steps Tools Needed QtyReplacing V-Belt To replace the V-beltShimming Table Blade Lead Correct blade leadSkewing your fence To shim the tableShifting Table To check if your wheels are coplanar Wheel AlignmentComponents and Hardware Needed Qty Coplanarity Gauge Wiring Wiring Safety Instructions110V Main Main Parts List DescriptionTrunnion Bracket Cast Iron Components DescriptionStand Labels Rear of MachineWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns Order Hours a DAY

G0457 specifications

The Grizzly G0457 is a versatile and robust woodworking tool designed to meet the needs of both amateur woodworkers and professional craftsmen. This cabinet-style bandsaw offers a blend of power, precision, and durability, making it an essential addition to any serious workshop.

One of the standout features of the G0457 is its powerful 2 HP motor, which provides ample strength to cut through a variety of materials, including hardwoods and softwoods. This motor is designed for consistent performance, minimizing the risk of stalling during operation. Furthermore, the bandsaw is equipped with a large cutting capacity, boasting a 14-inch resaw height and a 13-inch maximum cutting width, enabling users to tackle larger projects with ease.

The construction of the Grizzly G0457 is another key highlight. The machine features a solid cast iron frame that enhances stability and reduces vibrations during operation. This sturdy design contributes to improved accuracy, ensuring that cuts are clean and true. Furthermore, the oversized wheels are made of aluminum, allowing for smoother operation and a longer lifespan.

In terms of technology, the G0457 utilizes a precision-machined aluminum fence system. This system is designed for easy adjustments, providing users with the ability to make quick and accurate cuts. The bandsaw also includes a blade tension release, which simplifies blade changes and prolongs the lifespan of the blade itself. Additionally, the quick-release blade tension lever allows for easy adjustments, enhancing overall efficiency.

Safety features are also a priority in the design of the Grizzly G0457. It includes an easy-to-access power switch and a blade guard to protect users from potential injuries. The adjustable upper and lower blade guides ensure optimal performance and safety during operation.

The G0457 is also designed with convenience in mind. It includes a built-in dust port to help maintain a clean workspace. This feature minimizes dust accumulation, promoting a healthier environment and improving visibility while cutting.

In summary, the Grizzly G0457 bandsaw is a powerful and reliable tool that combines innovative features, robust construction, and user-friendly design. Whether you are ripping boards, resawing, or making intricate cuts, the G0457 stands out as a reliable choice for anyone serious about woodworking. Its attention to detail, performance capabilities, and safety features make it an invaluable asset in any workshop.
Top Page Image Contents