Grizzly G0457 owner manual Assembly, To assemble the bandsaw

Page 18

Assembly

To assemble the bandsaw:

1.Turn the cabinet stand upside down and install the feet, as shown in Figure 8.

Figure 8. Installing feet on cabinet.

2.Set the cabinet upright, move it to its final position, then adjust the feet so the cabinet is level side-to-side and front-to-back.

3.Secure the position of the feet by tightening the hex nut/washers against the stand.

The bandsaw body is heavy. DO NOT over-exert yourself while unpack- ing or moving your machine—get assistance from another person.

-16-

4.With the help of an assistant, set the bandsaw unit onto the stand, align the mounting holes, then open the door on the cabinet stand.

5.Have your assistant hold the bandsaw while you secure the body to the stand with the car- riage bolts and flange nuts (Figure 9).

Figure 9. Securing the body to the stand.

6.Slide the blade tension knob over the thread- ed shaft, as shown in Figure 10, and secure the knob with the flange screw.

Flange

Screw

Figure 10. Blade tension knob installed.

G0457 14" Industrial Bandsaw (Mfg. Since 5/11)

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model G0457 Industrial Bandsaw Page Table of Contents Introduction Manual Accuracy Contact InfoIdentification Machine Data Sheet Cutting Capacities Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Additional Safety Instructions for Bandsaws Full-Load Current Rating Power SupplyAvailability Circuit InformationGrounding Requirements Typical 5-20 plug and receptacleDisabling & Locking Switch Extension CordsVoltage Conversion Unpacking SetupNeeded for Setup Description QtyHardware Recognition Chart Contents Figures Qty InventoryHardware Not shown Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the bandsawTable installed on trunnions Installed front rail Dust Collection To connect a dust collection hoseBlade Tracking To center track the bladeChanges in the blade tension may change the blade tracking To test run the machine Test RunTable Stop Calibration Blade Tracking onTable Alignment To calibrate the pointer on the table tilt scaleFence Alignment To calibrate the miter gaugeTo align the fence parallel with the miter slot Blade Tensioning Adjusting Support BearingsTo adjust the support bearings To tension the bandsaw bladeTop View Blade Guide Adjustments To adjust the upper and lower blade guidesOperations Basic ControlsIrregular Cuts OverviewStraight Cuts Basic Cutting TipsWorkpiece Inspection Table TiltTo tilt the table To adjust guide post Guide Post RippingTo rip with the Model G0457 CrosscuttingResawing To crosscut with the Model G0457Cutting Curves To resaw a workpieceStacked Cuts To complete a stacked cutBlade Width Blade InformationBlade Length Tooth StyleBlade Breakage Tooth PitchBlade Care Most common causes of blade breakage areBlade Changes To remove the bladeTo replace the blade Accessories Half-mask respirator with disposable Cartridge filters H5408-Blade Tensioning GaugeG8984-Single Roller Stand G1928-Bandsaw HandbookG8983-Tilting Roller Stand G8985-5 Roller StandSchedule MaintenanceCleaning Unpainted Cast IronGuide Post Blade Tension LeadscrewRedressing Rubber Tires Table TrunnionsTo redress the rubber tires Service TroubleshootingMotor & Electrical Adjust the feet on the bottom of the stand relocate To check the V-belt Checking V-BeltTensioning V-Belt Steps Tools Needed QtyReplacing V-Belt To replace the V-beltSkewing your fence Shimming Table Blade LeadCorrect blade lead To shim the tableShifting Table Wheel Alignment Components and Hardware Needed QtyTo check if your wheels are coplanar Coplanarity Gauge Wiring Wiring Safety Instructions110V Main Main Parts List DescriptionTrunnion Bracket Cast Iron Components DescriptionStand Labels Rear of MachineWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns Order Hours a DAY

G0457 specifications

The Grizzly G0457 is a versatile and robust woodworking tool designed to meet the needs of both amateur woodworkers and professional craftsmen. This cabinet-style bandsaw offers a blend of power, precision, and durability, making it an essential addition to any serious workshop.

One of the standout features of the G0457 is its powerful 2 HP motor, which provides ample strength to cut through a variety of materials, including hardwoods and softwoods. This motor is designed for consistent performance, minimizing the risk of stalling during operation. Furthermore, the bandsaw is equipped with a large cutting capacity, boasting a 14-inch resaw height and a 13-inch maximum cutting width, enabling users to tackle larger projects with ease.

The construction of the Grizzly G0457 is another key highlight. The machine features a solid cast iron frame that enhances stability and reduces vibrations during operation. This sturdy design contributes to improved accuracy, ensuring that cuts are clean and true. Furthermore, the oversized wheels are made of aluminum, allowing for smoother operation and a longer lifespan.

In terms of technology, the G0457 utilizes a precision-machined aluminum fence system. This system is designed for easy adjustments, providing users with the ability to make quick and accurate cuts. The bandsaw also includes a blade tension release, which simplifies blade changes and prolongs the lifespan of the blade itself. Additionally, the quick-release blade tension lever allows for easy adjustments, enhancing overall efficiency.

Safety features are also a priority in the design of the Grizzly G0457. It includes an easy-to-access power switch and a blade guard to protect users from potential injuries. The adjustable upper and lower blade guides ensure optimal performance and safety during operation.

The G0457 is also designed with convenience in mind. It includes a built-in dust port to help maintain a clean workspace. This feature minimizes dust accumulation, promoting a healthier environment and improving visibility while cutting.

In summary, the Grizzly G0457 bandsaw is a powerful and reliable tool that combines innovative features, robust construction, and user-friendly design. Whether you are ripping boards, resawing, or making intricate cuts, the G0457 stands out as a reliable choice for anyone serious about woodworking. Its attention to detail, performance capabilities, and safety features make it an invaluable asset in any workshop.
Top Page Image Contents