Global Machinery Company ATBR1650-3PK instruction manual Risk of electric shock

Page 40

Risk to injury (cont.)

• Fasteners could ricochet or be propelled causing serious

• Never point discharge of tool at self or others.

injury or property damage.

• Do not pull trigger unless tool contact safety device is

 

 

against work surface.

 

• Never attempt to drive fasteners into hard surfaces such

 

as steel, concrete, or tile.

 

• Take care to avoid driving a fastener on top of another

 

fastener.

 

• Position tool carefully so that fasteners will be delivered

 

to the proper location.

 

• Do not drive fasteners close to the edge of the

 

workpiece. The workpiece is likely to split allowing the

 

fastener to fly free or ricochet causing personal injury.

 

 

• Improperly maintained tools and accessories can cause

• Maintain the tool with care.

serious injury.

• Always check that the striking element is operating

 

 

properly. Do not modify or disable the strike element, or

 

any tool parts.

 

 

• There is a risk of bursting if the tool is damaged.

• Check for misalignment or binding of moving parts,

 

breakage of parts, and any other condition that affects

 

the tool’s operation. If damaged, have the tool serviced

 

before using.

 

 

• Use only accessories identified by the manufacturer to

• Use of an accessory not intended for use with the

be used with specific tools.

specific tools, increases the risk of injury to persons.

 

 

Risk of electric shock

What could happen

How to prevent it

 

 

• Using air tools to attach electrical wiring may result in

• Never use a nailer to attach electrical wiring while

electrocution or death.

energized.

 

 

• Contact with a “live” wire will also make exposed metal

• Avoid body contact with grounded surfaces such as

parts of the tool “live” and may result in electrocution or

pipes, radiators, ranges, and refrigerators. There is an

death.

increased risk of electric shock if your body is grounded.

 

 

• Fasteners coming in contact with hidden electrical wiring

• Thoroughly investigate the workpiece for possible hidden

may cause electrocution or death.

wiring before performing work.

 

 

10

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Finishing Nail GUN KIT Contents Description of symbols SpecificationsIntroduction Environmental protectionGeneral safety instructions for air tools Page What could happen How to prevent it Important safety instructions Risk of eye or head injuryRisk of fire or explosion Risk of loss of hearing Risk to injuryRepair servicing should be done only by an authorized Risk of electric shock Risk of entanglement Risk of cut or burnsKnow your product Preparing the tool Tool lubricationWhere to use finishing nailer Checking the safety strike elementOperation Operating the tool Firing mechanismAdjusting the exhaust direction Adjusting the fastening depthAir source Clearing a jamTroubleshooting Magnesium Brad NAILER/STAPLER GUN Contents Introduction General safety instructions for air tools Page Important safety instructions Risk of eye or head injury Risk of loss of hearing Repair servicing should be done only by an authorized Risk of electric shock Risk of entanglement Know your product Preparing the tool Where to use brad nailer/stapler Air source Has loss of power Nailer/stapler skips whenDriving brad nails/staples Nailer/stapler runs slow orFraming GUN KIT Contents Nails General safety instructions Additional safety rules for framing gun nailers Page Important safety instructions Risk of eye or head injury Risk of loss of hearing Repair servicing should be done only by an authorized Risk of electric shock Risk of entanglement Non marking tip Air inlet not shown Selecting compressor Selecting air hose Tool lubricationWhere to use framing nailer Adjusting depth of nailingOperating the tool Single full sequential actuation firingConnecting the air hose MaintenanceMaintenance of nailer Maintenance of compressor, air settings and air hose CleaningRepairs Trouble Possible cause Suggested remedy Nailer skips when Driving nailsTool or in trigger area Nailer runs slow or has Air leaking near
Top Page Image Contents