Global Machinery Company DB305SMS Slide lock, Mitre table lock, Bevel lock, Bevel adjuster

Page 11

Slide lock

E

When tightened, the slide

 

lock (29) prevents the

 

saw head from sliding.

 

Tighten the slide lock during

 

transportation (fig. E).

 

 

 

Mitre table lock

 

F

The mitre table lock (25) is

 

used to lock the table at the

 

desired mitre angle (fig. F).

 

The mitre saw cuts from 0° to 45° both left and right. To adjust the mitre angle loosen the mitre table lock and using the mitre table handle

adjust the mitre angle to the desired position. The mitre table features positive click stops at 0°, 15°, 22.5°, 30° and 45° for quick setting of common mitre angles.

WARNING. Be sure to tighten the mitre table lock before making a cut. Failure to do so could result in the table moving during the cut and cause serious personal injury.

Bevel lock

G

The bevel lock (16) is used

 

to set the blade at the

 

desired bevel angle (fig. G).

 

The mitre saw bevel cuts

 

from 0° to 45° to the left

 

and right. To adjust the bevel

 

angle loosen the bevel lock

 

and pull out the 0° bevel

 

adjuster (18). Adjust the saw

 

arm to the desired bevel angle.

 

WARNING. Be sure to tighten the bevel lock before making a cut. Failure to do so could result in the saw arm moving during the cut and cause serious personal injury.0°

Bevel adjuster

 

H

The bevel adjuster (18)

 

needs to be pulled out before

 

the bevel angle can be

 

adjusted (fig. H).

 

To return the saw arm to

 

the vertical (0° bevel)

 

position move the saw arm

 

to the left and push in the

 

0° bevel adjuster.

 

Return the saw blade to the vertical position, it will automatically stop at the 0° bevel position. Tighten the bevel lock.

Clamp assembly

 

I

The clamp assembly (10)

 

can be mounted to the fence,

 

either side of the saw blade,

 

to suit the task at hand

 

(fig. I).

 

Use the clamp assembly lock

(11)at the back of the fence to secure the clamp assembly in position (fig. J).

J

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Double Bevel Slide Compound Mitre Saw Contents Introduction Description of symbolsSpecifications Dear CustomerDamage to hearing if effective earmuffs are not worn Safety rules for laser lightsGeneral safety instructions Page Additional safety rules for mitre saws Select saw blades in relation to the material being cut Wear gloves when handling saw blades and rough materialsTake additional care when trenching slotting Ensure that the arm is properly secure when bevellingAccessories Know your product Stabiliser bar UnpackingTransportation Bench mountingMitre table lock Bevel adjusterClamp assembly Slide lockDust bag Spindle lock buttonRotating lower Blade guard Turning on Redeye laser line Generator Setting the tableSwitch 24 fig. S Turning on and offRetighten the bevel lock Setting the fence Square with the tableTo the base fig. d Tighten the screws securing the fenceRaise the saw arm 5 to its highest position Changing a bladeRetighten the screw securing the mitre scale pointer That the inner blade Outer blade Washer where they Contact the bladeUp and press Direction as the blade Screw has a left hand Thread fig. lBy loosening the clamp Cross-cutting without slide actionAcross the grain Made with the mitre table Set at 0º fig. q. MitreAngled to the fence Cross-cutting With slide actionBevel cut Bevel cut is made byCompound mitre cut Adjusting the laser linesTowards the eye of a person for longer than 0.25s Using the laser line generatorDo not stare directly at the y laser beam General inspection Maintenance Power cord maintenanceCleaning Page Page Save this Manual for future reference
Top Page Image Contents