Global Machinery Company DB305SMS Wear gloves when handling saw blades and rough materials

Page 7

•Never use your hands to remove sawdust, chips or waste close by the blade.

•Use only blades as recommended by the manufacturer and which conform to EN 847-1.

•Do not use blades of High Speed Steel (HSS blades).

•If the table insert is damaged or worn, have it replaced by an authorised service centre.

•Rags, cloths, cord and string and the like should never be left around the work area.

•Avoid cutting nails. Inspect the workpiece and remove all nails and other foreign objects before beginning sawing.

•Support the work properly.

•Refrain from removing any cut-offs or other parts of the workpiece from the cutting area whilst the machine is running and the saw head is not in the rest position.

•Do not attempt to free a jammed blade before first switching off the machine.

•Do not slow or stop a blade with a piece of wood. Let the blade come to rest naturally.

•If you are interrupted when operating the saw, complete the process and switch off before looking up.

•Periodically check that all nuts, bolts and other fixings are properly tightened.

•Do not store materials or equipment above a machine in such a way that they could fall into it.

•Always hold the saw on parts that are insulated. If you accidentally cut into hidden wiring or the saw’s own cable, the metal parts of the saw will become “live”. Switch off at the mains and remove the plug immediately.• Never saw near combustible liquids or gases.

•Note the direction of rotation of the motor and the blade.

•Do not lock the movable guard in the open position and always ensure that it is working properly, freely rotating and returning to fully cover the teeth of the blade.

•Connect the saw to a dust collection devise and ensure

that it is operated properly. As the operator of the saw, please make sure that you understand factors that influence exposure to dust, including the type of material to be machined, the importance of local extraction and the proper adjustment of hoods/baffles/ shoots of your dust extraction system. We recommend that you always wear a dust mask when operating this saw.

•Wear gloves when handling saw blades and rough materials.

•Saw blades shall be carried in a holder wherever possible.

•Select saw blades in relation to the material being cut.

•Use correctly sharpened saw blades and observe the maximum speed marked on the blade.

•Take additional care when trenching (slotting).

•The mitre saw can be safely carried by the carrying handle but only once it has been removed from the mains power and secured in the locked down position.

•Ensure that the arm is properly secure when bevelling.

•Keep the floor area around the machine level, well maintained and free of loose materials.

•Ensure that you are trained in the use, adjustment and operation of the machine.

•Do not remove any cut-offs from the cutting area until the guard is fully locked in placed and the blade has come to rest.

•When cutting long pieces which extend well over the table width, ensure that the ends are adequately supported at the same height as the saw table top. Supports should be positioned in such a way to ensure that the workpiece does not fall to the ground once the cut has been made. A number of supports at regular intervals may be required if the workpiece is extremely long.

Wear goggles

Wear earmuffs

Wear a breathing mask

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Double Bevel Slide Compound Mitre Saw Contents Introduction Description of symbolsSpecifications Dear CustomerGeneral safety instructions Safety rules for laser lightsDamage to hearing if effective earmuffs are not worn Page Additional safety rules for mitre saws Select saw blades in relation to the material being cut Wear gloves when handling saw blades and rough materialsTake additional care when trenching slotting Ensure that the arm is properly secure when bevellingAccessories Know your product Stabiliser bar UnpackingTransportation Bench mountingMitre table lock Bevel adjusterClamp assembly Slide lockRotating lower Blade guard Spindle lock buttonDust bag Turning on Redeye laser line Generator Setting the tableSwitch 24 fig. S Turning on and offRetighten the bevel lock Setting the fence Square with the tableTo the base fig. d Tighten the screws securing the fenceRetighten the screw securing the mitre scale pointer Changing a bladeRaise the saw arm 5 to its highest position That the inner blade Outer blade Washer where they Contact the bladeUp and press Direction as the blade Screw has a left hand Thread fig. lBy loosening the clamp Cross-cutting without slide actionAcross the grain Made with the mitre table Set at 0º fig. q. MitreAngled to the fence Cross-cutting With slide actionBevel cut Bevel cut is made byCompound mitre cut Adjusting the laser linesDo not stare directly at the y laser beam Using the laser line generatorTowards the eye of a person for longer than 0.25s Cleaning Maintenance Power cord maintenanceGeneral inspection Page Page Save this Manual for future reference
Top Page Image Contents