Woodstock ST1000 owner manual Table of Contents

Page 3

Table of Contents

MODEL ST1000 SPECIFICATIONS	........................ 2
MACHINE FEATURES	3
SAFETY	4
Safety Instructions	4
POWER REQUIREMENTS	6
Operation	6
SETUP	7
Unpacking	7
Items Needed for Setup	7
Inventory	8
Cleanup	9
Site Considerations	9
Assembling Stand	10
Main Body	10
Motor & Switch	11
Installing Blade Guides	12
Table	13
Installing Positive Stop	13
Installing Fence	14
Dust Collection	15
Adjusting Positive Stop	15
Blade Tracking	16
Test Run	17
Tensioning Blade	17
Adjusting Support Bearings	18
Adjusting Blade Guides	19
Calibrating Table Tilt Scale	20
Aligning Table	21
Aligning Fence	21
Miter Gauge	22

OPERATIONS	23
Operation Safety	23
Overview	23
Key Switch	24
Guide Post	24
Blade Lead	25
Table Tilt	25
Ripping	26
Crosscutting	26
Resawing	27
Cutting Curves	28
Stacked Cuts	28
Blade Information	29
Blade Changes	31
MAINTENANCE	32
Schedule	32
Cleaning	32
Unpainted Cast Iron	32
Lubrication	32
SERVICE	33
Troubleshooting	33
Checking V-Belt	35
Tensioning V-Belt	35
Replacing V-Belt	36
Wheel Alignment	37
ST1000 Electrical Components	39
ST1000 Wiring Diagram	40
Main Breakdown	41
Main Breakdown Parts List	42
Fence Breakdown & Parts List	44
Safety Labels Breakdown & Parts List	45
WARRANTY	46
Warranty Registration	47

Image 3

Contents Manual Page Table of Contents Motor Model ST1000 SpecificationsFront view of bandsaw Machine FeaturesSafety Safety InstructionsZero Risk Does Not Exist Safety Instructions Operation Power RequirementsQty SetupItems Needed for Setup UnpackingHardware Qty InventoryMain Inventory Figure Qty Fence Inventory Figure QtyNecessary Space CleanupSite Considerations Floor LoadComponents and Hardware Needed Qty To install the main bodyAssembling Stand Main BodyTo install the motor and switch Motor & SwitchInstalling Blade Guides To install the lower blade guideTo install the upper blade guide assembly Installing Positive Stop To install the tableTo install the positive stop To install the fence Installing FenceAdjusting Positive Stop Dust CollectionTo set the positive stop Blade Tracking To center track the bladeChanges in the blade tension may change the blade tracking Test Run Tensioning BladeTo tension the bandsaw blade To adjust the support bearings Adjusting Support BearingsTo adjust the upper and lower blade guides Adjusting Blade GuidesTo calibrate the pointer on the table tilt scale Calibrating Table Tilt ScaleTo align the fence parallel with the miter slot Aligning TableAligning Fence To align the miter slot parallel to the bandsaw bladeTo calibrate the miter gauge Miter GaugeStraight Cuts Operation SafetyOperations OverviewKey Switch To adjust guide post assembly alignment on the guide postGuide Post Table Tilt Blade LeadTo crosscut with the Model ST1000 RippingCrosscutting To rip with the Model ST1000To resaw a workpiece ResawingCutting Curves Stacked CutsTo complete a stacked cut Tooth Style Blade InformationBlade Length Blade WidthMost common causes of blade breakage are Tooth PitchBlade Care Blade BreakageBlade Changes To remove the bladeTo replace the blade Unpainted Cast Iron MaintenanceCleaning ScheduleService TroubleshootingMotor Edge of the cut Workpiece OperationTools Needed Qty Checking V-BeltTensioning V-Belt To check the V-beltTo replace the V-belt Replacing V-BeltTo verify if the upper and lower wheels are copla- nar Wheel AlignmentTo Shim a Wheel ST1000 Electrical Components 110V Motor Wiring 220V Motor WiringST1000 Wiring Diagram Main Breakdown Description Main Breakdown Parts ListXPB73M Fence Breakdown & Parts List Safety Labels Breakdown & Parts List Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA