Woodstock ST1000 owner manual XPB73M

Page 45

Main Breakdown Parts List

REF	PART #	DESCRIPTION

100	XST1000100	KNOB M10-1.5
101	XPB73M	HEX BOLT M10-1.5 X 50
102	XPB82M	HEX BOLT M8-1.25 X 80
103	XPN03M	HEX NUT M8-1.25
104	XST1000104	MITER GAUGE ASSY
104-1	XST1000104-1	MITER BODY
104-2	XST1000104-2	MITER BAR
104-3	XST1000104-3	POINTER
104-4	XST1000104-4	WASHER PLASTIC
104-5	XPS19M	PHLP HD SCR M5-.8 X 6
104-6	XST1000104-6	PIN
104-7	XST1000104-7	KNOB 1/4” X 3/4”
105	XPSB31M	CAP SCREW M8-1.25 X 25
106	XPLW04M	LOCK WASHER 8MM
107	XPW01M	FLAT WASHER 8MM
108	XST1000108	STEEL BALL 5/16”
109	XST1000109	SPRING
110	XPSS30M	SET SCREW M10-1.5 X 10
111	XPTLW02M	EXT TOOTH WASHER 5MM
112	XST1000112	CORD CLAMP

REF	PART #	DESCRIPTION

113	XPS08M	PHLP HD SCR M5-.8 X 12
114	XPB83M	HEX BOLT M6 -1 X 16
115	XST1000115	TENSION POINTER
117	XST1000117	BASE PLATE
118	XST1000118	STRENGTHEN PLATE
119	XST1000119	LEG
120	XST1000120	SHORT BRACE
121	XST1000121	LONG BRACE
122	XPFN01M	FLANGE NUT M8-1.25
123	XPCB06M	CARRIAGE BOLT M8-1.25 X 16
124	XST1000124	BASE
125	XPB80M	HEX BOLT M16-2 X 55
126	XPW08M	FLAT WASHER 16MM
127	XPN13M	HEX NUT M16-2
128	XST1000128	PIN 1/4”
129	XST1000129	LOWER WHEEL SHAFT
130	XP6204	BEARING 6204ZZ
131	XPK23M	KEY 5 X 5 X 25
132	XPW01M	FLAT WASHER 8MM
133	XPS16M	PHLP HD SCR M8-1.25 X 16

ST1000 14" Bandsaw

-43-

Image 45

Contents Manual Page Table of Contents Motor Model ST1000 SpecificationsFront view of bandsaw Machine FeaturesSafety Safety InstructionsZero Risk Does Not Exist Safety Instructions Operation Power RequirementsItems Needed for Setup SetupUnpacking QtyMain Inventory Figure Qty InventoryFence Inventory Figure Qty Hardware QtySite Considerations CleanupFloor Load Necessary SpaceAssembling Stand To install the main bodyMain Body Components and Hardware Needed QtyTo install the motor and switch Motor & SwitchInstalling Blade Guides To install the lower blade guideTo install the upper blade guide assembly Installing Positive Stop To install the tableTo install the positive stop To install the fence Installing FenceAdjusting Positive Stop Dust CollectionTo set the positive stop Blade Tracking To center track the bladeChanges in the blade tension may change the blade tracking Test Run Tensioning BladeTo tension the bandsaw blade To adjust the support bearings Adjusting Support BearingsTo adjust the upper and lower blade guides Adjusting Blade GuidesTo calibrate the pointer on the table tilt scale Calibrating Table Tilt ScaleAligning Fence Aligning TableTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotTo calibrate the miter gauge Miter GaugeOperations Operation SafetyOverview Straight CutsKey Switch To adjust guide post assembly alignment on the guide postGuide Post Table Tilt Blade LeadCrosscutting RippingTo rip with the Model ST1000 To crosscut with the Model ST1000To resaw a workpiece ResawingCutting Curves Stacked CutsTo complete a stacked cut Blade Length Blade InformationBlade Width Tooth StyleBlade Care Tooth PitchBlade Breakage Most common causes of blade breakage areBlade Changes To remove the bladeTo replace the blade Cleaning MaintenanceSchedule Unpainted Cast IronService TroubleshootingMotor Edge of the cut Workpiece OperationTensioning V-Belt Checking V-BeltTo check the V-belt Tools Needed QtyTo replace the V-belt Replacing V-BeltTo verify if the upper and lower wheels are copla- nar Wheel AlignmentTo Shim a Wheel ST1000 Electrical Components 110V Motor Wiring 220V Motor WiringST1000 Wiring Diagram Main Breakdown Description Main Breakdown Parts ListXPB73M Fence Breakdown & Parts List Safety Labels Breakdown & Parts List Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA