Woodstock ST1000 owner manual Assembling Stand, Main Body, Components and Hardware Needed Qty

Page 12

Assembling Stand

Components and Hardware Needed:	Qty
Carriage Bolts M8-1.25 x 16	34
Hex Nuts M8-1.25	34
Base Plate	1
Legs	4
Side Leg Braces	2
Front/Rear Leg Braces	2
Support Braces	2
To assemble the stand:

1.Place the base plate upside down on a flat surface, and loosely attach the legs to the base plate with the carriage bolts and hex nuts.

Note: Install the carriage bolts with the round end facing out.

2.Loosely attach the front/rear leg braces and side braces to the legs, then turn the stand right side up. Make sure it sits level, then tighten all the hex nuts.

3.Place the support braces on the underside of the base plate, making sure the hole patterns match and are properly aligned.

4.Insert a carriage bolt through two end holes in each brace and loosely secure them as shown in Figure 7.

Figure 7. Carriage bolts in rear holes.

Main Body
Components and Hardware Needed:	Qty
Body Assembly	1
Hex Bolts M8-1.25 x 35	4
Hex Nuts M8-1.25	4
Flat Washers 8mm	4
Lock Washers 8mm	4

The Model ST1000 is a heavy machine (154 lbs.). DO NOT over-exert yourself while unpacking or moving your machine—get assis- tance.

To install the main body:

1.With the help of an assistant, set the body onto the stand and align the stand holes with the main body.

2.Have your assistant hold the main body in place and secure the main body to the stand (Figure 8) with the hex bolts, flat washers, lock washers, and hex nuts.

Figure 8. Securing main body to the stand.

-10-	ST1000 14" Bandsaw

Image 12

Contents Manual Page Table of Contents Model ST1000 Specifications MotorMachine Features Front view of bandsawSafety Safety InstructionsZero Risk Does Not Exist Safety Instructions Power Requirements OperationSetup Items Needed for SetupUnpacking QtyInventory Main Inventory Figure QtyFence Inventory Figure Qty Hardware QtyCleanup Site ConsiderationsFloor Load Necessary SpaceTo install the main body Assembling StandMain Body Components and Hardware Needed QtyMotor & Switch To install the motor and switchInstalling Blade Guides To install the lower blade guideTo install the upper blade guide assembly Installing Positive Stop To install the tableTo install the positive stop Installing Fence To install the fenceAdjusting Positive Stop Dust CollectionTo set the positive stop Blade Tracking To center track the bladeChanges in the blade tension may change the blade tracking Test Run Tensioning BladeTo tension the bandsaw blade Adjusting Support Bearings To adjust the support bearingsAdjusting Blade Guides To adjust the upper and lower blade guidesCalibrating Table Tilt Scale To calibrate the pointer on the table tilt scaleAligning Table Aligning FenceTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotMiter Gauge To calibrate the miter gaugeOperation Safety OperationsOverview Straight CutsKey Switch To adjust guide post assembly alignment on the guide postGuide Post Blade Lead Table TiltRipping CrosscuttingTo rip with the Model ST1000 To crosscut with the Model ST1000Resawing To resaw a workpieceCutting Curves Stacked CutsTo complete a stacked cut Blade Information Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areBlade Changes To remove the bladeTo replace the blade Maintenance CleaningSchedule Unpainted Cast IronService TroubleshootingMotor Operation Edge of the cut WorkpieceChecking V-Belt Tensioning V-BeltTo check the V-belt Tools Needed QtyReplacing V-Belt To replace the V-beltWheel Alignment To verify if the upper and lower wheels are copla- narTo Shim a Wheel 110V Motor Wiring 220V Motor Wiring ST1000 Electrical ComponentsST1000 Wiring Diagram Main Breakdown Main Breakdown Parts List DescriptionXPB73M Fence Breakdown & Parts List Safety Labels Breakdown & Parts List Warranty Warranty Registration CommentsBOX BELLINGHAM, WA