Woodstock ST1000 owner manual Motor & Switch, To install the motor and switch

Page 13

Motor & Switch
Components and Hardware Needed:	Qty
Motor	1
Switch	1
Cap Screws M8-1.25 x 25	2
Flat Washers 8mm	2
Lock Washers 8mm	2
Phillips Head Screws M5-.8 x 12	2
Phillips Head Screws M5-.8 x 15	2
External Tooth Lock Washers 5mm	2
Phillips Head Screw M5-.8 x 6	1
Star Washer 5mm	1
Metal Cord Clamp	1
Plastic Cord Clamp	1
To install the motor and switch:

1.Place the motor into the motor mounting area on the bottom of the main body (Figure 9).

Plastic Cord

Clamp Location

Figure 9. Placing motor on the body.

2.Loosely thread the cap screws, flat washers and lock washers into the motor (Figure 10).

Figure 10. Installed cap screws.

ST1000 14" Bandsaw

3.Place the V-belt on the pulley, move the motor to the left with moderate pressure, and tighten the cap screws.

4.Push the belt with moderate pressure. If the belt deflects more than 3/4", repeat Step 3.

5.Ground the switch with the M5-.8 x 6 Phillips head screw and 5mm star washer, then attach the switch to the body with the M5-.8 x 15 Phillips head screws and 5mm eternal tooth lock washer (Figure 11).

Front Cord

Clamp

Figure 11. Attaching the switch.

6.Secure the cords on the front of the bandsaw body with the metal cord clamp and an M5-.8 x 12 Phillips head screw.

7.Secure the cord on the rear of the bandsaw body with the plastic cord clamp and an M5-.8 x 12 Phillips head screw (Figure 9).

-11-

Image 13

Contents Manual Page Table of Contents Motor Model ST1000 SpecificationsFront view of bandsaw Machine FeaturesSafety Instructions SafetyZero Risk Does Not Exist Safety Instructions Operation Power RequirementsItems Needed for Setup SetupUnpacking QtyMain Inventory Figure Qty InventoryFence Inventory Figure Qty Hardware QtySite Considerations CleanupFloor Load Necessary SpaceAssembling Stand To install the main bodyMain Body Components and Hardware Needed QtyTo install the motor and switch Motor & SwitchTo install the lower blade guide Installing Blade GuidesTo install the upper blade guide assembly To install the table Installing Positive StopTo install the positive stop To install the fence Installing FenceDust Collection Adjusting Positive StopTo set the positive stop To center track the blade Blade TrackingChanges in the blade tension may change the blade tracking Tensioning Blade Test RunTo tension the bandsaw blade To adjust the support bearings Adjusting Support BearingsTo adjust the upper and lower blade guides Adjusting Blade GuidesTo calibrate the pointer on the table tilt scale Calibrating Table Tilt ScaleAligning Fence Aligning TableTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotTo calibrate the miter gauge Miter GaugeOperations Operation SafetyOverview Straight CutsTo adjust guide post assembly alignment on the guide post Key SwitchGuide Post Table Tilt Blade LeadCrosscutting RippingTo rip with the Model ST1000 To crosscut with the Model ST1000To resaw a workpiece ResawingStacked Cuts Cutting CurvesTo complete a stacked cut Blade Length Blade InformationBlade Width Tooth StyleBlade Care Tooth PitchBlade Breakage Most common causes of blade breakage areTo remove the blade Blade ChangesTo replace the blade Cleaning MaintenanceSchedule Unpainted Cast IronTroubleshooting ServiceMotor Edge of the cut Workpiece OperationTensioning V-Belt Checking V-BeltTo check the V-belt Tools Needed QtyTo replace the V-belt Replacing V-BeltTo verify if the upper and lower wheels are copla- nar Wheel AlignmentTo Shim a Wheel ST1000 Electrical Components 110V Motor Wiring 220V Motor WiringST1000 Wiring Diagram Main Breakdown Description Main Breakdown Parts ListXPB73M Fence Breakdown & Parts List Safety Labels Breakdown & Parts List Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA