Woodstock owner manual Model ST1000 Specifications, Motor

Page 4

MODEL ST1000 SPECIFICATIONS

Product Dimensions:
Weight	154 lbs.
Length/Width/Height	27" x 26" x 671⁄4"
Footprint (Length/Width)	24" x 22"
Shipping Dimensions:
Type	Cardboard
Content	Machine
Weight	165 lbs.
Length/Width/Height	45"L x 20"W x 15"H
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	3⁄4 HP
Voltage	.......................................................... 110/220V
Prewired	110V
Phase	Single
Amps	9/4.5A
Speed	1725 RPM
Cycle	60 Hz
Number Of Speeds	1
Power Transfer	V-Belt Drive
Bearings	Shielded and Lubricated
Main Specifications:
Operation
Blade Speed	3000 FPM
Table Tilt	Left 15˚, Right 45˚
Cutting Capacities
Maximum Cutting Height	61⁄4"
Throat Capacity Left of Blade	131⁄2"
Blade Information
Standard Blade Length	931⁄2"
Blade Width Range	1⁄8"–3⁄4"
Blade Guide Type	High Density Plastic
Rear Support Guide Type	Ball Bearing Roller
Table Information
Table Size	14"W x 14"L x 11⁄2"T
Floor-to-Table Height	437⁄8"
Construction
Table	Precision Ground Cast Iron
Fence	Aluminum
Base	Pre-Formed Steel
Body	Precision Ground Cast Iron
Wheels	Computer Balanced Aluminum
Blade Guides	Plastic Guide Blocks with Ball Bearing Rear Support
Paint	Powder Coated
Other Information
Wheel Diameter	133⁄4"
Dust Port Size	4"
Country of Origin	Taiwan

-2-	ST1000 14" Bandsaw

Image 4

Contents Manual Page Table of Contents Model ST1000 Specifications MotorMachine Features Front view of bandsawSafety Instructions SafetyZero Risk Does Not Exist Safety Instructions Power Requirements OperationSetup Items Needed for SetupUnpacking QtyInventory Main Inventory Figure QtyFence Inventory Figure Qty Hardware QtyCleanup Site ConsiderationsFloor Load Necessary SpaceTo install the main body Assembling StandMain Body Components and Hardware Needed QtyMotor & Switch To install the motor and switchTo install the lower blade guide Installing Blade GuidesTo install the upper blade guide assembly To install the table Installing Positive StopTo install the positive stop Installing Fence To install the fenceDust Collection Adjusting Positive StopTo set the positive stop To center track the blade Blade TrackingChanges in the blade tension may change the blade tracking Tensioning Blade Test RunTo tension the bandsaw blade Adjusting Support Bearings To adjust the support bearingsAdjusting Blade Guides To adjust the upper and lower blade guidesCalibrating Table Tilt Scale To calibrate the pointer on the table tilt scaleAligning Table Aligning FenceTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotMiter Gauge To calibrate the miter gaugeOperation Safety OperationsOverview Straight CutsTo adjust guide post assembly alignment on the guide post Key SwitchGuide Post Blade Lead Table TiltRipping CrosscuttingTo rip with the Model ST1000 To crosscut with the Model ST1000Resawing To resaw a workpieceStacked Cuts Cutting CurvesTo complete a stacked cut Blade Information Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areTo remove the blade Blade ChangesTo replace the blade Maintenance CleaningSchedule Unpainted Cast IronTroubleshooting ServiceMotor Operation Edge of the cut WorkpieceChecking V-Belt Tensioning V-BeltTo check the V-belt Tools Needed QtyReplacing V-Belt To replace the V-beltWheel Alignment To verify if the upper and lower wheels are copla- narTo Shim a Wheel 110V Motor Wiring 220V Motor Wiring ST1000 Electrical ComponentsST1000 Wiring Diagram Main Breakdown Main Breakdown Parts List DescriptionXPB73M Fence Breakdown & Parts List Safety Labels Breakdown & Parts List Warranty Warranty Registration CommentsBOX BELLINGHAM, WA