Woodstock W1754 owner manual Machine Placement, Lifting Planer, Hardware and Tools Not Shown

Page 12

W1754 20" Planer With Mobile Base

SET UP

Hardware and Tools (Not Shown)

 

• Hex Wrenches 3, 4, 5, 6mm

4

• Wrenches 8/10, 12/14, 17/19mm

3

• Set Screws M8-1.25 x 20 (Wings)

6

• Hex Bolts M8-1.25 x 35 (Wings)

6

• Flat Washers 8mm (Wings)

6

• Lock Washers 6mm (Wings)

6

Handwheel Bushing (Handwheel)

1

Handwheel Handle (Handwheel)

1

• Hex Nut M12-1.75 (Handwheel)

1

• Flat Washer 12mm (Handwheel)

1

• Key 4 x 4 x 20mm (Handwheel)

1

• Flange Bolts M6-1 x 12 (Dust Hood)

6

Machine Placement

Floor Load: This machine distributes a heavy load in a small footprint. Some floors may require additional bracing to support both machine and operator.

Working Clearances: Consider existing and anticipated needs, size of material to be processed through the machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your planer.

Lighting: Lighting should be bright enough to eliminate shadow and prevent eye strain.

Lifting Planer

The cabinet stand on the Model W1754 is equipped with lifting bars to lift and place the planer.

Before lifting the planer, remove the shipping brace. We recommend placing shop rags or cardboard between the forks and cabinet base so you do not scratch the paint.

Figure 4 shows an example of a typical planer being lifted correctly with a forklift by the lifting bars.

USE power lifting equipment to lift this planer. Otherwise, seri- ous personal injury may occur.

MAKE your shop “child safe." Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. NEVER allow untrained visitors in your shop when assembling, adjusting or operat- ing equipment.

Figure 4. Example of planer being lifted

using forklift.

-10-

Image 12
Contents Planer with Mobile Base Page Contents Introduction Woodstock Technical SupportIntroduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Specifications Electrical220V Operation Setup Items Needed for SetupUnpacking InventoryMachine Placement Lifting PlanerHardware and Tools Not Shown Cleaning Machine These items are coated and must be cleanedExtension Wings Extension wing fasteners Leveling controlsTo install the handwheel, do these steps To install the caster and foot pedal, do these stepsHandwheel, Dust Hood Caster Connecting to Power Gearbox Oil LevelTo check the gearbox oil level, do these steps Test Run To perform a test run, do these stepsRecommended Adjustments Tighten V-BeltsOperations GeneralBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed Speed Feed control knob positionsAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Accessories Planer AccessoriesOperations Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsPulley Alignment on Lubrication Service Inspecting KnivesTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these stepsTo adjust the chain tension, do these steps Chain TensionTable Parallelism Maximum Allowable TolerancesTo adjust the table parallelism, do these steps Table micro-adjustment screwsRollers, Breaker Pressure Bar Heights Distance Below Knife Edge at *BDCLocation Service To adjust roller spring tension, do these steps Spring TensionScale Calibration Loosen the chip deflector mounting bolts see FigureTo calibrate the scale, do these steps Anti-Kickback Fingers Anti-kickback fingersPulley Alignment Example of checking belt AlignmentW1754 Electrical Components Motor junction boxW1754 20 Planer With Mobile Base Troubleshooting Problem Possible Cause Corrective ActionCutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# DescriptionCutterheadpulley Gearbox Parts Breakdown Gearbox Parts List Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Warranty Registration CommentsBOX BELLINGHAM, WA