Woodstock W1754 owner manual Handwheel, Dust Hood Caster, To install the handwheel, do these steps

Page 15

W1754 20" Planer With Mobile Base

Handwheel, Dust Hood &

Caster

To install the handwheel, do these steps:

1.Place the bushing on the handwheel shaft.

2.Insert the 4 x 4 x 20 key into the shaft keyway.

3.Thread the handle into the handwheel.

4.Place the handwheel on the shaft and secure it with the M12-1.75 hex nut and flat washer, as shown in

Figure 7.

During the next step, you MUST connect your planer to a dust collection system. Accumulated wood chips could cause a malfunction, resulting in personal injury or damage to the planer.

To install the dust hood, do these steps:

1.Put on gloves and adjust the gap between the edge of the chip deflector and knife edge to 1/4".

2.Attach the dust hood to the planer with six M6-1 x 12 flange bolts as shown in Figure 8.

3.Attach the dust hood to the dust collector.

Note: To maximize work results and minimize clog- ging, chipout, etc., use a dust collector with a mini- mum of 600 CFM at the planer dust port.

Figure 7. Installing handwheel on shaft.

Figure 8. Dust hood attached.

SET UP

To install the caster and foot pedal, do these steps:

1.Remove the pin and hex bolt that are already mount- ed in the foot pedal bracket.

2.Align the caster with the mounting holes in the foot pedal bracket.

3.Insert the hex bolt removed in Step 1 into the hole in the back side of the caster assembly, thread the washer and locknut onto the bolt, and tighten the bolt just enough for it to be snug without hampering the pivot action of the caster.

-13-

Image 15

Contents Planer with Mobile Base Page Contents Woodstock Technical Support IntroductionIntroduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Specifications Electrical220V Operation Inventory SetupItems Needed for Setup UnpackingMachine Placement Lifting PlanerHardware and Tools Not Shown These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsTo install the handwheel, do these steps To install the caster and foot pedal, do these stepsHandwheel, Dust Hood Caster Connecting to Power Gearbox Oil LevelTo check the gearbox oil level, do these steps To perform a test run, do these steps Test RunTighten V-Belts Recommended AdjustmentsBasic steps of operating the planer are as follows OperationsGeneral Basic OperationOperation Tips Feed control knob positions Feed SpeedAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Planer Accessories AccessoriesOperations Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsPulley Alignment on Lubrication Service Inspecting KnivesTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar HeightsLocation Service Spring Tension To adjust roller spring tension, do these stepsScale Calibration Loosen the chip deflector mounting bolts see FigureTo calibrate the scale, do these steps Anti-kickback fingers Anti-Kickback FingersExample of checking belt Alignment Pulley AlignmentMotor junction box W1754 Electrical ComponentsW1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListCutterheadpulley Gearbox Parts Breakdown Gearbox Parts List Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty RegistrationBOX BELLINGHAM, WA