Woodstock W1754 owner manual Labels & Cosmetic Parts

Page 54

W1754 20" Planer With Mobile Base

Labels & Cosmetic Parts

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

				613	614	616	615	613
	612			613	614
			601
611				602
611		600		602
		600
				617

603

610

609

608

607

606

605

604

REF	PART�#	DESCRIPTION
600	XLABEL-12	READ�MANUAL�LABEL
601	X1754601	MACHINE�ID�LABEL
602	XLABEL-11	SAFETY�GLASSES�LABEL
603	X1754603	SPEED�CHANGE�LABEL
604	X1754604	DECORATIVE�STRIPE�TAPE
605	X1754605	MODEL�NUMBER�LABEL
606	X1754606	SHOP�FOX�LOGO�PLATE
607	X1754607	SHOP�FOX�WHITE
608	XLABEL-1	EAR�PROTECTION�LABEL

REF	PART�#	DESCRIPTION
609	X1754609	RESPIRATOR�LABEL
610	XLABEL-04	ELECTRICITY�LABEL
611	X1754611	CONTROL�PANEL�LABEL
612	XPPAINT-7	SHOP�FOX�BLACK
613	X1754613	LUBRICATION�LABEL
614	X1754614	CUTTERHEAD�WARNING�LABEL
615	X1754615	DISCONNECT�POWER�LABEL
616	X1754616	SHUT�COVER�WARNING�LABEL
617	X1754617	HAND�WHEEL�LABEL

PARTS

-52-

Image 54

Contents Planer with Mobile Base Page Contents Introduction Woodstock Technical SupportIntroduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Specifications Electrical220V Operation Unpacking SetupItems Needed for Setup InventoryMachine Placement Lifting PlanerHardware and Tools Not Shown Cleaning Machine These items are coated and must be cleanedExtension Wings Extension wing fasteners Leveling controlsTo install the handwheel, do these steps To install the caster and foot pedal, do these stepsHandwheel, Dust Hood Caster Connecting to Power Gearbox Oil LevelTo check the gearbox oil level, do these steps Test Run To perform a test run, do these stepsRecommended Adjustments Tighten V-BeltsBasic Operation OperationsGeneral Basic steps of operating the planer are as followsOperation Tips Feed Speed Feed control knob positionsAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Accessories Planer AccessoriesOperations Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsPulley Alignment on Lubrication Service Inspecting KnivesTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these stepsTo adjust the chain tension, do these steps Chain TensionTable Parallelism Maximum Allowable TolerancesTo adjust the table parallelism, do these steps Table micro-adjustment screwsRollers, Breaker Pressure Bar Heights Distance Below Knife Edge at *BDCLocation Service To adjust roller spring tension, do these steps Spring TensionScale Calibration Loosen the chip deflector mounting bolts see FigureTo calibrate the scale, do these steps Anti-Kickback Fingers Anti-kickback fingersPulley Alignment Example of checking belt AlignmentW1754 Electrical Components Motor junction boxW1754 20 Planer With Mobile Base Troubleshooting Problem Possible Cause Corrective ActionCutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# DescriptionCutterheadpulley Gearbox Parts Breakdown Gearbox Parts List Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Warranty Registration CommentsBOX BELLINGHAM, WA