Black & Decker FS1802BN, FS1202BN Charging Procedure, Replace Pack, Wall Mounting a

Page 6

905013144 wo depth 11/28/06 7:43 AM Page 6

RECOMMENDED MINIMUM WIRE SIZE

FOR EXTENSION CORDS

TOTAL LENGTH OF CORD

 

 

 

 

25 FT.

50 FT.

75 FT.

100 FT.

125 FT.

150 FT.

175 FT.

7.6 M

15.2 M

22.9 M

30.5 M

38.1 M

45.7 M

53.3 M

WIRE SIZE AWG

 

 

 

 

 

18

18

16

16

14

14

12

9.Use only the supplied charger when charging your tool. The use of any other charger could damage the drill or create a hazardous condition.

10.Use only one charger when charging.

11.Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center.

12.DO NOT incinerate the battery packs even if they are severely damaged or completely worn out. The batteries can explode in a fire.

13.A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:

a.Wash quickly with soap and water.

b.Neutralize with a mild acid such as lemon juice or vinegar.

c.If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.

Charging Procedure

Your charger is designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any other voltage. Charge time is 60 minutes depending on battery pack type and condition.

1. Plug the charger into an appropriate outlet. NOTE: Do not charge by means of an engine generator or DC power source. Use only 1 120V AC.

2.Insert the battery pack into the charger (Figure 1). Be sure the pack is fully seated in the charger. The red (charging) light will blink continuously indicating that the charging process has started.

3. The completion of charge will be indicated by the red light remaining ON continuously. The battery pack is fully charged and may be used at this time or left in the charger.

4.Unplug charger, and remove the battery pack. Place the battery in

the tool and be certain that it is inserted fully into the tool

cavity until it “clicks” into place.2

NOTE: To remove the battery pack from the product, press down on the release button on the back of the battery (Figure 2) and pull out.

Replace Pack

The charger is designed to detect certain problems that can arise with

battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack. If problem persists, try a different battery pack to determine if the charger is OK. If the new pack charges correctly, then the original pack is defective and should be returned to a service center for recycling. If the new battery pack gives the same trouble indication as the original, have charger tested at an authorized service center.

Wall Mounting (Figure 2A)

A hole is provided in the center of the charger for mounting on a vertical surface.

2A

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Before Returning this Product For ANY Reason Please Call Work Area Electrical SafetyPersonal Safety Tool Use and CareImportant Safety Instructions for Nailers ServiceWo depth 11/28/06 743 AM Safety Warnings and Instructions Charging Battery Cap InformationCharging Procedure Replace PackWall Mounting a Features Leaving the Battery Pack in the ChargerImportant Charging Notes Operating Instructions LED Status Indicator FigureUsing the Lock-Off Figure Loading the Tool FigureClearing a Jammed Nail Figure MaintenanceRbrc Seal Belt Clip FS1202BN onlyFull Two-Year Home Use Warranty AccessoriesService Information Problem Possible Cause SolutionSpecial Warranty Note to Contractors Aire de travail Mesures de sécurité ÉlectricitéSécurité personnelle Directives de sécurité importantes relatives aux cloueurs Utilisation et entretien de l’outilEntretien Wo depth 11/28/06 743 AM Information concernant le capuchon du bloc-pile Directives et consignes de sécurité Chargement Calibre AWGMéthode de chargement Voyant de bloc-piles à remplacerFixation murale a Conserver CES Directives À Titre DE Référence CaractéristiquesUtilisation du Verrouillage Fig Mode demploiVoyant Del FIG Chargement de l’outil FigDésenrayage de clou Fig Pince-ceinture FS1202BNEntretien / Nettoyage Information sur les services Problème Cause probable SolutionAccessoires Garantie complète de deux ans pour usage résidentiel800 544-6986afin d’en obtenir de nouvelles sans frais Guarde Este Manual Para Futuras Consultas Área de trabajo Seguridad eléctricaSeguridad personal Instrucciones de seguridad importantes para clavadoras Uso y cuidados de la herramientaServicio Wo depth 11/28/06 743 AM Información acerca del protector de la batería Se han incluido protectores para el almacenaje yAdvertencias e instrucciones de seguridad Carga Calibre AWGMontaje en la pared Figura 2A Procedimiento de cargaCambio de la unidad de alimentación Permanencia de la unidad de alimentación en el cargadorGuarde Estas Instrucciones Para Referencia Futura CaracterísticasUso del bloqueo en off Figura Instrucciones de funcionamientoIndicador LED de condición Figura Carga de la herramienta FiguraMantenimiento / Limpieza Cómo despejar un clavo atorado FiguraSujetador de cinturón Figura 7 FS1202BN El sello RbrcInformación de servicio Problema Causa posible SoluciónAccesorios Garantía completa de dos años para uso domésticoNota especial de Garantía para Contratistas Podrá SER Cubierto Bajo Nuestra GarantíaWo depth 11/28/06 743 AM

FS1202BN, FS1802BN specifications

The Black & Decker FS1802BN and FS1202BN are two powerful and versatile tools designed to cater to the needs of both DIY enthusiasts and professionals. These products embody the quality and innovation that Black & Decker is known for, offering features that enhance efficiency and user-friendliness.

The FS1802BN is an 18V cordless drill with an impressive battery life and performance. It is engineered with a powerful motor that delivers ample torque for various applications, making it suitable for drilling through wood, metal, and plastic. The drill's variable speed settings allow users to adjust the speed according to the task at hand, providing greater control and precision. The ergonomic handle is designed for comfort during prolonged use, reducing fatigue and enhancing grip. Additionally, its compact design means it can easily fit into tight spaces, making it ideal for intricate projects.

On the other hand, the FS1202BN is a lightweight, user-friendly corded drill that packs a punch despite its smaller size. It features a powerful 120V motor that ensures consistent performance without the worry of battery life. The FS1202BN is equipped with a keyless chuck, allowing for quick and easy bit changes without the need for additional tools. This model also includes an integrated LED work light, illuminating dark work areas and making it easier to see what you're doing, an essential feature when working on detailed tasks.

Both drills share technologies that embody convenience and safety. They are equipped with built-in overload protection, which prevents the motor from overheating, extending the tool's life. Furthermore, the incorporated forward/reverse switch allows users to easily switch between drilling and un-drilling tasks, enhancing versatility.

In terms of design, both models feature a sleek, modern look with a durable build that can withstand the rigors of various work environments. The easy-to-reach controls ensure that users can operate the devices efficiently, enhancing their overall experience.

In conclusion, the Black & Decker FS1802BN and FS1202BN stand out in their categories by combining performance, versatility, and user-centric features. Whether for home improvement projects or professional tasks, these tools are designed to meet the demands of a wide range of applications, making them reliable choices for anyone looking to invest in high-quality drilling solutions.
Top Page Image Contents