Manual de Instrucciones | Modelo IFN3490 and IFN2190 |
Operating Instructions | Model IFN3490 and IFN2190 |
|
|
Unidos continentales, comuníquese con nosotros al
Clavos et Repuestos
Use solamente sujetadores Campbell Hausfeld originales (o su equivalente) - (vea la información sobre intercambio de sujetadores). Use solamente partes de repuesto Campbell Hausfeld originales. Nunca substituya las partes. No use partes modificadas o partes que no den un rendimiento equivalente al equipo original. El rendimiento de las herramientas, la
seguridad y la duración pueden verse reducidos. Cuando ordene partes de repuesto o sujetadores, especifique el número de la parte.
Para reparar la clavadora
Las reparaciones de la clavadora las debe hacer SOLAMENTE un técnico calificado que tenga experiencia.
Para colocarle los sellos
Cada vez que repare una clavadora deberá limpiarle y lubricarle las partes internas. Le recomendamos que use
Parker
compressor manufacturer for information.
Operating The Nailer
Read this manual and understand all safety warnings and instructions before operating the nailer.
LUBRICATION
This nailer requires lubrication before using the nailer for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis.
NOTICE
The work surface
RECOMMENDED HOOKUP |
| |
1. The air | 70 psi | |
compressor | ||
Min. | ||
must be able | 120 psi | |
to maintain a | ||
Max. | ||
minimum of 70 | ||
|
psi when the nailer is being used. An inadequate air supply can cause a loss of power and inconsistent driving.
2. An oiler can be used to provide oil circulation through the nailer. A filter
REMOVING
1. Disconnect air supply from nailer.
2.Remove all fasteners from magazine (See UNLOADING THE
NAILER).
3.Remove
Retaining
Ring 
Sujetadores
La herramienta IFN2190 también coloca sujetadores diseñados para: Sears 18465, Porter Cable FR350, Hitachi NR83A, y Senco FramePro 702XP, 752XP, Ridgid R350RHA y DeWalt D51844, D51845.
La herramienta IFN3490 también coloca sujetadores diseñados para: Porter Cable FC 350A, Hitachi NR83AA2, Senco FramePro 701XP, 751XP , Ridgid R350CHA, DeWalt D51822, D51823 y Paslode
can become
damaged by excessive lubrication. Proper lubrication is the owner’s responsibil- ity. Failure to lubricate the nailer properly will dramatically shorten the life of the nailer and void your warranty.
1. Disconnect the air supply from the nailer to add lubricant.
2. Turn the nailer |
| |
so the air inlet | OIL | |
is facing up. | ||
| ||
Place |
| |
of 30 W non- |
| |
detergent oil |
| |
into air inlet. |
| |
Do not use |
| |
detergent oils, oil additives, or air | ||
tool oils. Air tool oils contain | ||
solvents which will damage the | ||
nailer’s internal components. | ||
3. After adding oil, run nailer briefly. Wipe off any excess oil from the cap exhaust.
can be used to remove liquid and
solid impurities which can rust or “gum up” internal parts of the nailer.
3. Use 3/8” air
hoses with a minimum working
pressure of 150 psi. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug (1/4” NPT threads) with an inside diameter of .315” (8mm) on the nailer and a 3/8” quick coupler on the air hose.
4.Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the nailer between 70 and 120 psi.
NO-MAR DECKING TIP
The
4. Pry no- | No- |
mar tip | |
away | Mar |
from the | Tip |
| |
work |
|
contact | Work |
element. | Contact |
| Element |
5.Replace retaining
ring onto
tip, then store tip in safe
place for future use.
INSTALLING NO-MAR DECKING TIP
1. Disconnect air supply from nailer.
2.Remove all fasteners from magazine (See UNLOADING THE NAILER).
3.Remove retaining ring from
www.chpower.com
Recommended Hookup |
|
|
| |
Quick | Quick | Quick Plug | Regulator | |
| ||||
(Optional) | Oiler | |||
Plug | Coupler | |||
|
| Quick |
| |
|
| Coupler |
| |
|
| (Optional) |
| |
|
| Air |
| |
|
| Hose |
| |
|
|
| Filter | |
|
| 3 |
|