RIDGID SP6263 manual On-Product Safety Labels

Page 10

Safety

On-Product Safety Labels

There are several safety labels on the saw. They alert the user to hazards explained in the manual and remind the user how to avoid the hazard.

At the outfeed side, to the right of the guard near the saw handle is this safety label to alert you to wrong way feed:

On the infeed side of the guard is this safety label to remind you to lower the hold down to just clear the top of the workpiece for ripping:

On the rear of the yoke, visible from the infeed side when the saw is in a rip position, is this safety label to alert you to outfeed zone hazard:

Note where they are located on the saw. Read and follow the safety information and instructions in these labels. Refer to the manual for detailed explanations and instructions.

10

Image 10
Contents RS1000 Table of Contents Read and follow all safety information and instructions SafetySafety Symbol and Signal Words Major HazardsKickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Arsenic and chromium from chemi- cally-treated lumberSaw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label Introduction AssemblyIdentify Parts This model includes16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Attach Elevation Crank Mounting SawElevate arm approximately 3 to 4 Inches Attaching Carriage Motor to Arm Install arm cap Make certain power cord is unpluggedLock miter/arm lock before proceeding Remove saw blade Attach Table SupportsAdjustments Yoke Clamp Adjustment Bevel Lock Lever Adjusting Column Tube in Column Support Arm to Column AdjustmentAlignment Checks Alignment Adjustments Adjusting Carriage Bearings Lock Lnstalling Front Table Five Counterbored Holes Top Bottom Channel ClipMake Front Table Flat To lower center, tighten center 1-3/4 long pan head screwSquare Crosscut Travel Alignment and Adjustment StepsAlignment Squaring cross cut travelAlignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Align Riving Knife to Blade Raise riving knife and tighten pawls/riving knife knobControls Bevel index lever must be unindexed before moving motorYoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Motor Specifications Electrical ConnectionsMotor Protection & Reset Button Extension CordsTo Change Motor Voltage to 240 Volt A.C Crosscutting Crosscutting SafetyCrosscutting Defined Crosscut Kerfs Keep one hand on saw handle through stepMaking Crosscuts Repetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed DirectionsRipping Kickback To reduce risk of kickback Tial barrier to outfeed sideHold Down Function Pawls and Riving Knife FunctionRipping Set-up Procedure Follow these steps before rippingMaking Rip Cuts Keep Hand Edging Dado Blades, Molding HeadsRipping Hints Cutting Aides Putting it together Making the HandleAuxiliary Fence Molding/Sanding FeatherboardCutting Aids H.A. RequirementsAccessories Safety AccessoriesInformation for Edging General Information MaintenanceLubrication Replacing Pawls Lubricating Blade Guard AssemblyAdjusting the Trigger Blade ChangingTroubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Saw Problem Possible Causes What to DoPage Repair Repair Parts Always order by Part Number Not by Key NumberRepair Yoke Assembly Parts44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What we will do to correct problems What is coveredHow can you get service What is not covered