RIDGID SP6263 manual Lnstalling Front Table, Five Counterbored Holes Top Bottom Channel Clip

Page 26

Adjustments

lnstalling Front Table

1.Set out:

-front table

-tee nut

-1/4" U-clip

-1/4" diam. x 1" long cup point set screw

-four 1/4" diam x 1" long pan head screws

-1/4" diam. x 1-3/4" long pan head screw

-five 17/64" I.D. x 5/8" O.D. flat wash- ers

- four 1/4" lock washers

-four 1/4" diam. hex nuts.

2.Identify top and bottom of front table: top has counterbored holes. Place table bottom side up on solid surface. Hammer tee nut

into leveling hole. (This hole is not

T-Nut

counter-bored from the top).

 

3.Snap U-clip onto front edge of base so hole lines up with hole just to the left of cen- ter notch.

Five Counterbored Holes

Top

Bottom

Channel

U-Clip

4.Place table, top side up, on saw so center counterbored hole lines up with hole in U-clip. Note: Table will extend over front edge of saw frame.

26

Image 26
Contents RS1000 Table of Contents Read and follow all safety information and instructions SafetySafety Symbol and Signal Words Major HazardsKickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Arsenic and chromium from chemi- cally-treated lumberSaw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label Introduction AssemblyIdentify Parts This model includes16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Elevate arm approximately 3 to 4 Inches Mounting SawAttach Elevation Crank Lock miter/arm lock before proceeding Install arm cap Make certain power cord is unpluggedAttaching Carriage Motor to Arm Remove saw blade Attach Table SupportsAdjustments Yoke Clamp Adjustment Bevel Lock Lever Alignment Checks Arm to Column AdjustmentAdjusting Column Tube in Column Support Alignment Adjustments Adjusting Carriage Bearings Lock Lnstalling Front Table Five Counterbored Holes Top Bottom Channel ClipMake Front Table Flat To lower center, tighten center 1-3/4 long pan head screwSquare Crosscut Travel Alignment and Adjustment StepsAlignment Squaring cross cut travelAlignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Align Riving Knife to Blade Raise riving knife and tighten pawls/riving knife knobControls Bevel index lever must be unindexed before moving motorYoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Motor Specifications Electrical ConnectionsMotor Protection & Reset Button Extension CordsTo Change Motor Voltage to 240 Volt A.C Crosscutting Defined Crosscutting SafetyCrosscutting Crosscut Kerfs Keep one hand on saw handle through stepMaking Crosscuts Repetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed DirectionsRipping Kickback To reduce risk of kickback Tial barrier to outfeed sideHold Down Function Pawls and Riving Knife FunctionRipping Set-up Procedure Follow these steps before rippingMaking Rip Cuts Keep Hand Ripping Hints Dado Blades, Molding HeadsEdging Cutting Aides Auxiliary Fence Making the HandlePutting it together Molding/Sanding FeatherboardCutting Aids H.A. RequirementsInformation for Edging AccessoriesAccessories Safety Lubrication MaintenanceGeneral Information Replacing Pawls Lubricating Blade Guard AssemblyAdjusting the Trigger Blade ChangingTroubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Saw Problem Possible Causes What to DoPage Repair Repair Parts Always order by Part Number Not by Key NumberRepair Yoke Assembly Parts44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What we will do to correct problems What is coveredHow can you get service What is not covered