RIDGID SP6263 Make Front Table Flat, To lower center, tighten center 1-3/4 long pan head screw

Page 27

Adjustments

5.Drop a flat washer into each counter- bored hole.

6.Start 1-3/4"long pan head screw through center hole and into U-clip, but do not fully tighten.

7.Start cup point set screw through leveling hole and into tee nut, but do not fully tighten.

8.Put 1" long pan head screw in each of four remaining holes and through matching holes in table supports. Place lockwasher and nut on the end of each screw, and tighten with screwdriver.

	1/4-20 x 1-3/4"	17/64"
		Flat Washer
	Pan Head Screw

1/4-20 x 1"

Cup Point Set Screw

1/4-20 x 1"

Pan Head Screw

Front Table

Lockwasher

Hex Nut

Make Front Table Flat

1.Place rear table on its edge, across cen- ter of front table. Check for gap between sur- faces.

If there is a gap, close gap by raising or low- ering center of front table:

to raise center, tighten cup point set screw against frame;

to lower center, tighten center (1-3/4" long) pan head screw.

2.When gap is closed, make sure cup point set screw touches frame (look underneath table), and center (1-3/4" long) pan head screw is tightened.

Rear Table
Board	Hold Down	Leveling
	Hold Down	Leveling
	Screw	Set Screw

Front Table

This concludes adjusting your saw where you have removed all "looseness" or slack between the different parts of the saw. The next section deals with actually aligning the sawblade to get accu- rate cuts.

27

Image 27

Contents RS1000 Table of Contents Major Hazards SafetySafety Symbol and Signal Words Read and follow all safety information and instructionsKickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Arsenic and chromium from chemi- cally-treated lumber Safety InstructionsPersonal Safety Instructions Work Area Safety InstructionsWorkpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label This model includes AssemblyIdentify Parts Introduction16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Mounting Saw Attach Elevation CrankElevate arm approximately 3 to 4 Inches Install arm cap Make certain power cord is unplugged Attaching Carriage Motor to ArmLock miter/arm lock before proceeding Attach Table Supports Remove saw bladeAdjustments Yoke Clamp Adjustment Bevel Lock Lever Arm to Column Adjustment Adjusting Column Tube in Column SupportAlignment Checks Alignment Adjustments Adjusting Carriage Bearings Lock Five Counterbored Holes Top Bottom Channel Clip Lnstalling Front TableTo lower center, tighten center 1-3/4 long pan head screw Make Front Table FlatSquaring cross cut travel Alignment and Adjustment StepsAlignment Square Crosscut TravelAlignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Raise riving knife and tighten pawls/riving knife knob Align Riving Knife to BladeBevel index lever must be unindexed before moving motor ControlsYoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Electrical Connections Motor SpecificationsExtension Cords Motor Protection & Reset ButtonTo Change Motor Voltage to 240 Volt A.C Crosscutting Safety CrosscuttingCrosscutting Defined Keep one hand on saw handle through step Crosscut KerfsMaking Crosscuts Repetitive Crosscutting Infeed and Outfeed Directions RippingRipping Defined In-Rip and Out-Rip PositionsRipping Kickback Tial barrier to outfeed side To reduce risk of kickbackPawls and Riving Knife Function Hold Down FunctionFollow these steps before ripping Ripping Set-up ProcedureMaking Rip Cuts Keep Hand Dado Blades, Molding Heads EdgingRipping Hints Cutting Aides Making the Handle Putting it togetherAuxiliary Fence Featherboard Molding/SandingH.A. Requirements Cutting AidsAccessories Accessories SafetyInformation for Edging Maintenance General InformationLubrication Blade Changing Lubricating Blade Guard AssemblyAdjusting the Trigger Replacing PawlsTroubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Possible Causes What to Do Saw ProblemPage Repair Always order by Part Number Not by Key Number Repair PartsRepair Parts Yoke Assembly44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What is not covered What is coveredHow can you get service What we will do to correct problems