RIDGID SP6263 manual Repair Parts, Always order by Part Number Not by Key Number

Page 71

PARTS LIST FOR RIDGID 10" RADIAL SAW

MODEL NUMBER RS10000

Always order by Part Number - Not by Key Number

Figure 1

	Key	Part No.	Description
	No	Part No.	Description
	No


	1	804423-1	Cord, with Plug
	2	75090	Cover, Rear Arm
	3	60342	Bolt Square Head
			3/8-16 x 2-1/4 High Strength
	4	60353	Washer, .380 x 47/64 x 1/8
	5	815649	Bearing, Arm
	6	60249	Nut, Lock 3/8-16
	7	13848	Screw, Pan Rec. Hd 10-32 Ty T x 1/2
	8	827922	Scale, Miter
	9	827923	Indicator, Miter
	10	827905	Trim Arm
	11	63686	Pad, Trim
	12	805494	Nut, Square 3/8-16
	13	60391	Screw, Pan Rec. Ty AB 10 x 3/4
	14	827924	Knob, Lever Arm
	15	—	Arm Assembly, See Fig. 5
	16	131201	Lockwasher, 5/16
	17	9421620	Screw, Soc. Hd Cap 5/16-18 x 1/2
	18	—	Yoke Assembly, See Fig. 2
	19	809491-6	Screw, Pan Hd 1/4-20 x 1-3/4
	20	822079	Table, Rear
	21	822080	Table, Spacer

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	22	63432	Fence, Rip
	23	822078	Table, Front
	24	141667-33	Screw, Set SL. Cup 1/4-20 x 1
	25	805552-7	Washer, 17/64 x 5/8 x 1/32
	26	809491-1	Screw, Pan Hd 1/4-20 x 1
	27	145544	Nut, Tee
	28	37530	Nut, "U" Clip
	29	115109	Lockwasher, 1/4
	30	115120	Nut, Hex 1/4-20
	31	826284	Clamp Assembly
	32	—	Base Assembly, See Fig. 3
	33	63467	Cap, Flag Terminal
	34	60339	Bolt, Sq. Hd 3/8-16 x 2-1/4 Gr 5
	35	63881	Clamp, Cord
	36	9420417	Screw, Type “T” Hex Washer Hd 1/4-20 x 5/8
	37	827950	Guard Assembly, See Fig. 4
	38	63683	Wrench, Hex "U” 3/16
	39	63682	Wrench, Hex "U” 1/4
	40	822384-1	Wrench
	41	SP6263	Owners Manual - English
	42	SP6263S	Owners Manual - Spanish
	43	SP6263F	Owners Manual - French

71

* Standard Hardware Item - May Be Purchased Locally

Repair Parts

Image 71

Contents RS1000 Table of Contents Major Hazards SafetySafety Symbol and Signal Words Read and follow all safety information and instructionsKickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Arsenic and chromium from chemi- cally-treated lumber Safety InstructionsPersonal Safety Instructions Work Area Safety InstructionsWorkpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label This model includes AssemblyIdentify Parts Introduction16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Elevate arm approximately 3 to 4 Inches Mounting SawAttach Elevation Crank Lock miter/arm lock before proceeding Install arm cap Make certain power cord is unpluggedAttaching Carriage Motor to Arm Attach Table Supports Remove saw bladeAdjustments Yoke Clamp Adjustment Bevel Lock Lever Alignment Checks Arm to Column AdjustmentAdjusting Column Tube in Column Support Alignment Adjustments Adjusting Carriage Bearings Lock Five Counterbored Holes Top Bottom Channel Clip Lnstalling Front TableTo lower center, tighten center 1-3/4 long pan head screw Make Front Table FlatSquaring cross cut travel Alignment and Adjustment StepsAlignment Square Crosscut TravelAlignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Raise riving knife and tighten pawls/riving knife knob Align Riving Knife to BladeBevel index lever must be unindexed before moving motor ControlsYoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Electrical Connections Motor SpecificationsExtension Cords Motor Protection & Reset ButtonTo Change Motor Voltage to 240 Volt A.C Crosscutting Defined Crosscutting SafetyCrosscutting Keep one hand on saw handle through step Crosscut KerfsMaking Crosscuts Repetitive Crosscutting Infeed and Outfeed Directions RippingRipping Defined In-Rip and Out-Rip PositionsRipping Kickback Tial barrier to outfeed side To reduce risk of kickbackPawls and Riving Knife Function Hold Down FunctionFollow these steps before ripping Ripping Set-up ProcedureMaking Rip Cuts Keep Hand Ripping Hints Dado Blades, Molding HeadsEdging Cutting Aides Auxiliary Fence Making the HandlePutting it together Featherboard Molding/SandingH.A. Requirements Cutting AidsInformation for Edging AccessoriesAccessories Safety Lubrication MaintenanceGeneral Information Blade Changing Lubricating Blade Guard AssemblyAdjusting the Trigger Replacing PawlsTroubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Possible Causes What to Do Saw ProblemPage Repair Always order by Part Number Not by Key Number Repair PartsRepair Parts Yoke Assembly44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What is not covered What is coveredHow can you get service What we will do to correct problems