RIDGID SP6263 manual Attaching Carriage Motor to Arm, Lock miter/arm lock before proceeding

Page 17

Assembly

Attaching Carriage - Motor to Arm

Remove carriage stop screw, lockwasher and tag. Read and understand warning tag before discarding tag.

Lock miter/arm lock before proceeding.

Holding carriage assembly with both hands, carefully start and slide the carriage onto the tracks. The assembly must be held parallel with the arm so that all four bearings slide smoothly onto the arm, preventing any excessive strain on bearings and track.

WARNING

Reinstall carriage stop screw and lock- washer to prevent carriage from rolling off arm. Tighten carriage stop screw securely.

Note: Remove two (2) motor packing studs that are threaded into bottom of motor.

Packing

Studs

Install arm cap.

WARNING

Make certain power cord is unplugged.

1.Insert finger under left end of switch lever and pull out to the "ON" position.

2.Place arm cap in position and install with

(2) 10-32 x 7/8 self threading screws.

3.Push switch to "OFF" position.

Warning

Tab

Lockwasher

Stop Screw

Hex “L” Wrench 1/4 Inch (Supplied)

Push toward rear of

Miter/Arm

Lock Lever

saw to lock

 

Bottom

of Motor

Arm Cap

Screw

Reinstall carriage stop screw and lockwasher

17

Image 17
Contents RS1000 Table of Contents Safety Symbol and Signal Words SafetyRead and follow all safety information and instructions Major HazardsKickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Personal Safety Instructions Safety InstructionsWork Area Safety Instructions Arsenic and chromium from chemi- cally-treated lumberWorkpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label Identify Parts AssemblyIntroduction This model includes16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Elevate arm approximately 3 to 4 Inches Mounting SawAttach Elevation Crank Lock miter/arm lock before proceeding Install arm cap Make certain power cord is unpluggedAttaching Carriage Motor to Arm Attach Table Supports Remove saw bladeAdjustments Yoke Clamp Adjustment Bevel Lock Lever Alignment Checks Arm to Column AdjustmentAdjusting Column Tube in Column Support Alignment Adjustments Adjusting Carriage Bearings Lock Five Counterbored Holes Top Bottom Channel Clip Lnstalling Front TableTo lower center, tighten center 1-3/4 long pan head screw Make Front Table FlatAlignment Alignment and Adjustment StepsSquare Crosscut Travel Squaring cross cut travelAlignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Raise riving knife and tighten pawls/riving knife knob Align Riving Knife to BladeBevel index lever must be unindexed before moving motor ControlsYoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Electrical Connections Motor SpecificationsExtension Cords Motor Protection & Reset ButtonTo Change Motor Voltage to 240 Volt A.C Crosscutting Defined Crosscutting SafetyCrosscutting Keep one hand on saw handle through step Crosscut KerfsMaking Crosscuts Repetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed DirectionsRipping Kickback Tial barrier to outfeed side To reduce risk of kickbackPawls and Riving Knife Function Hold Down FunctionFollow these steps before ripping Ripping Set-up ProcedureMaking Rip Cuts Keep Hand Ripping Hints Dado Blades, Molding HeadsEdging Cutting Aides Auxiliary Fence Making the HandlePutting it together Featherboard Molding/SandingH.A. Requirements Cutting AidsInformation for Edging AccessoriesAccessories Safety Lubrication MaintenanceGeneral Information Adjusting the Trigger Lubricating Blade Guard AssemblyReplacing Pawls Blade ChangingTroubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Possible Causes What to Do Saw ProblemPage Repair Always order by Part Number Not by Key Number Repair PartsRepair Parts Yoke Assembly44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number How can you get service What is coveredWhat we will do to correct problems What is not covered