RIDGID SP6263 manual Front Table Fence

Page 30

Alignment

	Install Table Clamps
	1. Insert fence, then spacer table, then rear	Front Table	Fence	Spacer	Rear
	table.	Front Table	Fence	Table	Table
	table.			Table	Table

2.Tilt table clamp bracket forward and snap into place in opening at rear of left and right table support.

3.Tighten thumbscrews to clamp table sec- tions in place.

Insert Table Clamp

Bracket

30

Image 30

Contents RS1000 Table of Contents Read and follow all safety information and instructions SafetySafety Symbol and Signal Words Major HazardsKickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Arsenic and chromium from chemi- cally-treated lumberSaw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label Introduction AssemblyIdentify Parts This model includes16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Mounting Saw Attach Elevation CrankElevate arm approximately 3 to 4 Inches Install arm cap Make certain power cord is unplugged Attaching Carriage Motor to ArmLock miter/arm lock before proceeding Remove saw blade Attach Table SupportsAdjustments Yoke Clamp Adjustment Bevel Lock Lever Arm to Column Adjustment Adjusting Column Tube in Column SupportAlignment Checks Alignment Adjustments Adjusting Carriage Bearings Lock Lnstalling Front Table Five Counterbored Holes Top Bottom Channel ClipMake Front Table Flat To lower center, tighten center 1-3/4 long pan head screwSquare Crosscut Travel Alignment and Adjustment StepsAlignment Squaring cross cut travelAlignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Align Riving Knife to Blade Raise riving knife and tighten pawls/riving knife knobControls Bevel index lever must be unindexed before moving motorYoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Motor Specifications Electrical ConnectionsMotor Protection & Reset Button Extension CordsTo Change Motor Voltage to 240 Volt A.C Crosscutting Safety CrosscuttingCrosscutting Defined Crosscut Kerfs Keep one hand on saw handle through stepMaking Crosscuts Repetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed DirectionsRipping Kickback To reduce risk of kickback Tial barrier to outfeed sideHold Down Function Pawls and Riving Knife FunctionRipping Set-up Procedure Follow these steps before rippingMaking Rip Cuts Keep Hand Dado Blades, Molding Heads EdgingRipping Hints Cutting Aides Making the Handle Putting it togetherAuxiliary Fence Molding/Sanding FeatherboardCutting Aids H.A. RequirementsAccessories Accessories SafetyInformation for Edging Maintenance General InformationLubrication Replacing Pawls Lubricating Blade Guard AssemblyAdjusting the Trigger Blade ChangingTroubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Saw Problem Possible Causes What to DoPage Repair Repair Parts Always order by Part Number Not by Key NumberRepair Yoke Assembly Parts44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What we will do to correct problems What is coveredHow can you get service What is not covered