SUPER MICRO Computer SBI-7426T-S3 user manual Ahci Configuration Sub-menu Menu Option

Page 60

SBI-7426T-S3 Blade Module User’s Manual

Table 6-9. AHCI Configuration Sub-menu

Menu Option

AHCI BIOS Support

AHCI CD/DVD Boot Time Out

AHCI Port0~Port5

SATA Port0 ~

Port5

S.M.A.R.T.

Description

This option enables AHCI BIOS support on your system. Options include Enabled and DISABLED.

This sets the timeout time in seconds for AHCI CD/DVD boot drives. Some SATA CD/DVD drives in AHCI mode need to wait longer than others. Options include 0 (sec), 5, 10, 15, 20, 25, 30 and 35.

While entering setup, BIOS auto detects the presence of IDE devices. This setting displays the status of auto detection of IDE devices.

For this setting, select the type of device connected to the system. Select Auto to allow the AMI BIOS to automatically detect a hard disk drive in your system. Options include Auto and NOT INSTALLED.

Self-Monitoring Analysis and Reporting Technology (SMART) can help predict impending drive failures. Select DISABLED to prevent the AMI BIOS from using S.M.A.R.T in your system. Selecting Enabled allows the AMI BIOS to use S.M.A.R.T to support the hard disk drive. Option include DISABLED and Enabled.

Table 6-10. Event Log Configuration Sub-menu

Menu Option

View Event Log

Mark All Events as Read

Clear Event Log

Description

Selecting this option allows you to view all unread events on the Event Log.

This option makrs all events as read. Options ae OK and Cancel when selected.

This option clears the Event Log memory of all messages. Options are OK and Cancel.

 

 

Table 6-11. IPMI Configuration Sub-menu

 

 

Menu Option

Description

 

The Baseboard Management Controller (BMC) manages the interface between

Status of BMC

the system management software and platform hardware. This non-configurable

 

informational feature shows the status code of the BMC micro controller.

 

 

 

This feature displays the BMC System Event Log (SEL). This log shows the total

 

number of entries of BMC system events. To view an event, select an entry

 

number and press <ENTER> to display the information as shown in the screen.

 

This screen contains the following information:

 

• Total Number of Entries

 

SEL Entry Number

View BMC System

SEL Record ID

SEL Record Type

Event Log

 

Timestamp, Generator ID

 

• Event Message Format User

 

Event Sensor Type

 

Event Sensor Number

 

Event Dir Type

 

Event Data

 

 

 

6-12

Image 60
Contents SBI-7426T-S3 Blade Module User’s Manual SBI-7426T-S3 Blade Module User’s Manual Preface About this ManualManual Organization SBI-7426T-S3 Blade Module User’s Manual Table of Contents Blade Module Features Vii Viii List of Figures Full Rack of Blade Enclosures and Blade ServersSBI-7426T-S3 Blade Module User’s Manual List of Tables Xii Product Checklist of Typical Components Chapter IntroductionOverview SBI-7426T-S3 Blade Specification Features ProcessorsMemory Storage DensityContacting Supermicro HeadquartersEurope Asia-PacificChapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions Electrostatic Discharge PrecautionsOperating Precautions Chapter Setup and Installation Installing Blade ModulesPowering Up a Blade Unit Powering Down a Blade UnitInstalling a Blade Unit into the Enclosure Removing/Replacing the Blade CoverInserting a Blade into the Enclosure Processor Installation Removing a ProcessorOnboard Battery Installation Installing a Processor in a SocketMemory Installation Populating Memory SlotsProcessor DIMMs ChannelSlot Dimm Numbering Dimm Installation Installing a Dimm into a Memory SlotHard Disk Drive Installation Removing a Hard Drive CarrierInstalling a Hard Drive in a Carrier Installing the Operating System Installing with an External USB CD-ROM DriveInstalling via PXE Boot Configuring and Setting up RAID Installing via Virtual Media Drive RedirectionManagement Software Chapter Blade Module Features SBI-7426T-S3 Blade Module FeaturesDescription Control Panel Blade Control Panel Function State DescriptionPower Button LED IndicatorsKVM Connector KVM ButtonMainboard B8DT6 MainboardIntel 5500 Tylersburg Chipset Block Diagram B8DT6 Mainboard LayoutJumpers Cmos ClearBlade Unit Components Main Components of SBI-7426T-S3 Blade ModuleMemory Support Hard Disk DrivesChapter RAID Setup Procedure Important NotesBios Configuration Utilities Bios Setup Advanced Settings ScreenIDE Configuration Screen Configure RAID Drives Selecting Max Ports Option Selecting RAID Utility Enabling Hot Plug Exit Bios Setup Screen Message SBI-7426T-S3 Blade Module User’s Manual Chapter IntroductionBios Updates Flashing BiosRunning Setup Type flash filename.romMain Bios Setup Main Setup Menu ScreenAdvanced Setup Main Bios Setup Menu OptionsMenu Option Description Advanced Setup Menu Options Sub-menu DescriptionCPU and Clock Configuration Sub-menu Menu Option IDE Configuration Menu Menu OptionIDE Configuration Menu PCIPnP Configuration Sub-menu Menu OptionSuperIO Configuration Sub-menu Menu Option Chipset Configuration Sub-menu Menu OptionDMA Acpi Configuration Sub-menu Menu Option Ahci Configuration Sub-menu Menu Option 10. Event Log Configuration Sub-menu Menu Option11. Ipmi Configuration Sub-menu 11. Ipmi Configuration Sub-menu Menu Option 12. MPS Configuration Sub-menu Menu Option 13. PCI Express Configuration Sub-menu Menu Option14. Smbios Configuration Sub-menu Menu Option 15. Remote Access Configuration Sub-menuSecurity 16. System Health Monitor Sub-menu Menu Option17. Security Menu Options Boot 18. Boot Setup Menu Options18. Boot Setup Menu Options Description Force Bios or Keep CurrentExit 19. Exit Menu OptionsCPU Temperature Hardware Health InformationSystem Temperature Voltage MonitoringSBI-7426T-S3 Blade Module User’s Manual Appendix a Bios Post Codes Bios Post MessagesTable A-1. Bios Post Messages Bios Message CPU ID Bios Post Codes Recoverable Post Errors Terminal Post ErrorsTable A-2. Terminal Post Errors Post Code DescriptionTable A-2. Terminal Post Errors SBI-7426T-S3 Blade Module User’s Manual Table A-2. Terminal Post Errors Post Code Table A-3. Boot Block Flash ROM Terminal Post Errors Page SBI-7426T-S3 Blade Module User’s Manual Disclaimer SBI-7426T-S3 Blade Module User’s Manual