Sears 315.11485 manual Safety Rules for Charger

Page 51

SAFETY RULES FOR CHARGER

WARNING! READ AND UNDERSTAND ALL

INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

nBefore using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.

CAUTION: To reduce the risk of electric shock or damage to the charger and battery, charge only nickel-cadmium rechargeable batteries as specifi- cally designated on your charger. Other types of batteries may burst, causing personal injury or damage.

nDo not use charger outdoors or expose to wet or damp conditions. Water entering charger will increase the risk of electric shock.

nUse of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

nDo not abuse cord or charger. Never use the cord to carry the charger. Do not pull the charger cord rather than the plug when disconnecting from receptacle. Damage to the cord or charger could occur and create an electric shock hazard. Replace damaged cords im- mediately.

nMake sure cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts or otherwise subject- ed to damage or stress. This will reduce the risk of accidental falls, which could cause injury, and damage to the cord, which could result in electric shock.

nKeep cord and charger from heat to prevent damage to housing or internal parts.

nDo not let gasoline, oils, petroleum-based products, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic.

nAn extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25’

50’

100’

Cord Size (AWG)

16

16

16

NOTE: AWG = American Wire Gauge

nDo not operate charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger replaced by an authorized serviceman.

nDo not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized serviceman for electrical check to determine if the charger is in good working order.

nDo not disassemble charger. Take it to an authorized serviceman when service or repair is required. Incor- rect reassembly may result in a risk of electric shock or fire.

nUnplug charger from outlet before attempting any maintenance or cleaning to reduce the risk of electric shock.

nDisconnect charger from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It also will help prevent damage to the charger during a power surge.

nRisk of electric shock. Do not touch uninsulated portion of output connector or uninsulated battery terminal.

nSave these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instruc- tions also to prevent misuse of the product and possible injury.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

5

Image 51
Contents Operators Manual Table of Contents WarrantyIntroduction Work Area General Safety RulesElectrical Safety Personal SafetyAdditional Rules for Safe Operation Specific Safety RulesService Rules for Battery ToolsSafety Instructions for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Specifications Features Unpacking InstructionsPacking List Operation Battery PackCharging Battery Pack Information for Recharging Cool Battery PackTo Install Battery Pack To Remove Battery PackTWO-SPEED Gear Train Lock Tighten Chuck Body Switch Forward TriggerReversible Drill BITRemoving Bits Installing BitsAdjustable Torque Clutch To Adjust TorqueScrewdriver BIT BIT Storage Area DrillingMallet HEX KEY Chuck RemovalTo Retighten a Loose Chuck Mallet Chuck JawsMaintenance Battery Pack Removal and Preparation for RecyclingBatteries Page Craftsman 1/2 in., 19.2 Volt Cordless DRILL-DRIVER Model no See Back page for Parts Ordering Instructions Parts ListGet it fixed, at your home or ours Operators Manual ONE Year Full Warranty on Craftsman Tool Work Area Electrical SafetyPersonal Safety Model Battery Pack ChargerCauses and Operator Prevention of Kickback Laser Guide Warnings Safety Rules for Charger Symbols Service Spindle Lock Button Laser Guide RIP Product SpecificationsAssembly Installing Battery Pack Latches Battery PackAttaching Blade To Tighten Edge Installing Edge GuideRemoving Blade Spindle Lock Screw To LoosenCharging the Battery Pack Charging a Cool Battery PackApplications Charging a HOT Battery Pack Kickback Incorrect SupportCorrect Support Kickback Blade Guard System Lower Blade Guard Is in UP Position When Making a CUTSwitch Trigger Blade Exposed on Underside of Workpiece SAW BladesAdjustment Knob Adjusting Blade DepthUsing the Laser Guide Depth Base Assembly TightenWrong Correct WR ONG Operating the SAWCross CUTTING/RIP Cutting Bevel Scale To Adjust Bevel SettingBevel Adjustment Knob Scale Blade Guide Notch Bevel CuttingTo Adjust Positive 0 Bevel Stop Positive 0 Bevel StopTo Check Positive 0 Bevel Stop Pocket CUT Lower Blade Guard AdjustmentsAdjusting the Laser Pocket CuttingGeneral Maintenance LubricationReplacing Laser Guide Batteries Accessories Battery Pack Removal Preparation for RecyclingBatteries Number Model 3733KEY Part Number Description QTY Craftsman 19.2 Volt Cordless Trim SAW Model NumberVolt Reciprocating Saw Variable Speed Table of Contents General Safety Rules Specific Safety Rules Safety Rules for Charger Symbols Service Volts DC HEX KEY Holder SwitchKnow Your Reciprocating SAW Toolless Blade ClampAssembly Battery Pack Shown Charger To Attach To Remove / Attach Battery PackBattery Port Battery Pack Latch To Install SAW Blade To RemovePivot Base Shoe AssemblyTo Change Positions of Base Assembly General CuttingMetal Cutting Plunge CuttingMaintenance Blade Types Length See Back page for Parts Ordering Instructions Craftsman 19.2 Volt Reciprocating SAW Model noGet it fixed, at your home or ours Volt Fluorescent Light Warranty General Safety Rules Specific Safety Rules Important Safety Instructions for Charger Symbols Operation Switch Maintenance Battery Pack Removal and Preparation for Recycling Page Get it fixed, at your home or ours