Sears 315.11485 manual Important Safety Instructions for Charger

Page 69

SPECIFIC SAFETY RULES

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

Save these instructions. This manual contains important safety and operating instructions for charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, and product using battery charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce risk of injury, charge only nickel- cadmium type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not expose charger to wet or damp conditions. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce risk of damage to charger body and cord, pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Following this rule will reduce the risk of serious personal injury.

An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25'

50'

100'

Cord Size (AWG)

16

16

16

Note: AWG = American Wire Gage

Do not operate charger with a damaged cord or plug. If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of elec- tric shock or fire. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce the risk of electric shock, unplug charger from outlet before attempting any mainte- nance or cleaning. Turning off controls will not reduce this risk. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Disconnect charger from power supply when not in use. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

SAVE THESE INSTRUCTIONS

5

Image 69
Contents Operators Manual Table of Contents WarrantyIntroduction Electrical Safety General Safety RulesPersonal Safety Work AreaService Specific Safety RulesRules for Battery Tools Additional Rules for Safe OperationSafety Instructions for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Specifications Features Unpacking InstructionsPacking List Charging Battery Pack Battery PackInformation for Recharging Cool Battery Pack OperationTo Install Battery Pack To Remove Battery PackTWO-SPEED Gear Train Reversible Switch Forward TriggerDrill BIT Lock Tighten Chuck BodyAdjustable Torque Clutch Installing BitsTo Adjust Torque Removing BitsScrewdriver BIT BIT Storage Area DrillingTo Retighten a Loose Chuck Chuck RemovalMallet Chuck Jaws Mallet HEX KEYMaintenance Battery Pack Removal and Preparation for RecyclingBatteries Page Craftsman 1/2 in., 19.2 Volt Cordless DRILL-DRIVER Model no See Back page for Parts Ordering Instructions Parts ListGet it fixed, at your home or ours Operators Manual ONE Year Full Warranty on Craftsman Tool Personal Safety Electrical SafetyModel Battery Pack Charger Work AreaCauses and Operator Prevention of Kickback Laser Guide Warnings Safety Rules for Charger Symbols Service Spindle Lock Button Laser Guide RIP Product SpecificationsAssembly Installing Battery Pack Latches Battery PackAttaching Blade Removing Blade Installing Edge GuideSpindle Lock Screw To Loosen To Tighten EdgeCharging the Battery Pack Charging a Cool Battery PackApplications Charging a HOT Battery Pack Kickback Incorrect SupportCorrect Support Kickback Switch Trigger Blade Exposed on Underside of Workpiece Lower Blade Guard Is in UP Position When Making a CUTSAW Blades Blade Guard SystemUsing the Laser Guide Adjusting Blade DepthDepth Base Assembly Tighten Adjustment KnobWrong Correct WR ONG Operating the SAWCross CUTTING/RIP Cutting Bevel Adjustment Knob Scale Blade Guide Notch To Adjust Bevel SettingBevel Cutting Bevel ScaleTo Adjust Positive 0 Bevel Stop Positive 0 Bevel StopTo Check Positive 0 Bevel Stop Adjusting the Laser AdjustmentsPocket Cutting Pocket CUT Lower Blade GuardGeneral Maintenance LubricationReplacing Laser Guide Batteries Accessories Battery Pack Removal Preparation for RecyclingBatteries Number Model 3733KEY Part Number Description QTY Craftsman 19.2 Volt Cordless Trim SAW Model NumberVolt Reciprocating Saw Variable Speed Table of Contents General Safety Rules Specific Safety Rules Safety Rules for Charger Symbols Service Volts DC Know Your Reciprocating SAW SwitchToolless Blade Clamp HEX KEY HolderAssembly Battery Pack Shown Charger Battery Port Battery Pack Latch To Install SAW Blade To Remove / Attach Battery PackTo Remove To AttachTo Change Positions of Base Assembly Base Shoe AssemblyGeneral Cutting PivotMetal Cutting Plunge CuttingMaintenance Blade Types Length See Back page for Parts Ordering Instructions Craftsman 19.2 Volt Reciprocating SAW Model noGet it fixed, at your home or ours Volt Fluorescent Light Warranty General Safety Rules Specific Safety Rules Important Safety Instructions for Charger Symbols Operation Switch Maintenance Battery Pack Removal and Preparation for Recycling Page Get it fixed, at your home or ours