Sears 315.11485 manual Battery Pack Removal and Preparation for Recycling

Page 74

MAINTENANCE

BATTERIES

The battery pack for this light is equipped with nickel- cadmium rechargeable batteries. Length of service from each charging will depend how much the light is used.

The batteries in the battery pack have been designed to provide maximum trouble free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.

To obtain the longest possible battery life, we suggest the following:

Store and charge the battery pack in a cool area. Temperatures below 50°F or above 100° F will shorten battery life.

Never store battery pack in a discharged condition. Recharge battery immediately when it becomes discharged.

All batteries gradually lose their charge. The higher the temperature the quicker they lose their charge. If you store your light for long periods of time without using it, recharge the batteries every month or two. This practice will prolong battery life.

To preserve natural resources, please recycle or dispose of batteries properly.

This product contains nickel-cadmium batteries. Local, state or federal laws may prohibit disposal of nickel-cadmium batteries in ordinary trash.

Consult your local waste authority for information regarding available recycling and/or disposal options.

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

WARNING: Upon removal, cover the battery pack's terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings can result in fire and/or serious injury.

WARNING: Do not attempt to disassemble the battery pack. Fire or injury can result.

10

Image 74
Contents Operators Manual Introduction Table of ContentsWarranty Personal Safety General Safety RulesElectrical Safety Work AreaRules for Battery Tools Specific Safety RulesService Additional Rules for Safe OperationSafety Instructions for Charger Symbols Symbol Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Specifications Features Packing List UnpackingInstructions Information for Recharging Cool Battery Pack Battery PackCharging Battery Pack OperationTWO-SPEED Gear Train To Install Battery PackTo Remove Battery Pack Drill BIT Switch Forward TriggerReversible Lock Tighten Chuck BodyTo Adjust Torque Installing BitsAdjustable Torque Clutch Removing BitsDrilling Screwdriver BIT BIT Storage AreaMallet Chuck Jaws Chuck RemovalTo Retighten a Loose Chuck Mallet HEX KEYBatteries MaintenanceBattery Pack Removal and Preparation for Recycling Page See Back page for Parts Ordering Instructions Parts List Craftsman 1/2 in., 19.2 Volt Cordless DRILL-DRIVER Model noGet it fixed, at your home or ours Operators Manual ONE Year Full Warranty on Craftsman Tool Model Battery Pack Charger Electrical SafetyPersonal Safety Work AreaCauses and Operator Prevention of Kickback Laser Guide Warnings Safety Rules for Charger Symbols Service Product Specifications Spindle Lock Button Laser Guide RIPAssembly Attaching Blade Installing Battery PackLatches Battery Pack Spindle Lock Screw To Loosen Installing Edge GuideRemoving Blade To Tighten EdgeApplications Charging the Battery PackCharging a Cool Battery Pack Charging a HOT Battery Pack Correct Support Kickback KickbackIncorrect Support SAW Blades Lower Blade Guard Is in UP Position When Making a CUTSwitch Trigger Blade Exposed on Underside of Workpiece Blade Guard SystemDepth Base Assembly Tighten Adjusting Blade DepthUsing the Laser Guide Adjustment KnobOperating the SAW Wrong Correct WR ONGCross CUTTING/RIP Cutting Bevel Cutting To Adjust Bevel SettingBevel Adjustment Knob Scale Blade Guide Notch Bevel ScaleTo Check Positive 0 Bevel Stop To Adjust Positive 0 Bevel StopPositive 0 Bevel Stop Pocket Cutting AdjustmentsAdjusting the Laser Pocket CUT Lower Blade GuardReplacing Laser Guide Batteries General MaintenanceLubrication Batteries AccessoriesBattery Pack Removal Preparation for Recycling 3733 Number ModelCraftsman 19.2 Volt Cordless Trim SAW Model Number KEY Part Number Description QTYVolt Reciprocating Saw Variable Speed Table of Contents General Safety Rules Specific Safety Rules Safety Rules for Charger Symbols Service Volts DC Toolless Blade Clamp SwitchKnow Your Reciprocating SAW HEX KEY HolderAssembly Battery Pack Shown Charger To Remove To Remove / Attach Battery PackBattery Port Battery Pack Latch To Install SAW Blade To AttachGeneral Cutting Base Shoe AssemblyTo Change Positions of Base Assembly PivotPlunge Cutting Metal CuttingMaintenance Blade Types Length Craftsman 19.2 Volt Reciprocating SAW Model no See Back page for Parts Ordering InstructionsGet it fixed, at your home or ours Volt Fluorescent Light Warranty General Safety Rules Specific Safety Rules Important Safety Instructions for Charger Symbols Operation Switch Maintenance Battery Pack Removal and Preparation for Recycling Page Get it fixed, at your home or ours