Sears 315.11485 manual Warranty

Page 66

 

 

TABLE OF CONTENTS

Warranty

2

Introduction

2

General Safety Rules

3

Specific Safety Rules

4-5

Symbols

6

Operation

7-8

Maintenance

9-10

Parts, Ordering, and Service

12

WARRANTY

FULL ONE YEAR WARRANTY ON CRAFTSMAN FLUORESCENT LIGHT

If this Fluorescent Light fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will repair it, free of charge.

If this Fluorescent Light is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

INTRODUCTION

Your fluorescent light has many features for making the use of this product more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate.

WARNING: Do not attempt to use this product until you thoroughly read and completely under- stand the operator’s manual. Pay close attention to the safety rules, including Dangers, Warnings, and Cautions. If you use this product properly and only as intended, you will enjoy years of safe, reliable service.

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.

2

Image 66
Contents Operators Manual Table of Contents WarrantyIntroduction Personal Safety General Safety RulesElectrical Safety Work AreaRules for Battery Tools Specific Safety RulesService Additional Rules for Safe OperationSafety Instructions for Charger Symbols Symbol Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Specifications Features Unpacking InstructionsPacking List Information for Recharging Cool Battery Pack Battery PackCharging Battery Pack OperationTo Install Battery Pack To Remove Battery PackTWO-SPEED Gear Train Drill BIT Switch Forward TriggerReversible Lock Tighten Chuck BodyTo Adjust Torque Installing BitsAdjustable Torque Clutch Removing BitsDrilling Screwdriver BIT BIT Storage AreaMallet Chuck Jaws Chuck RemovalTo Retighten a Loose Chuck Mallet HEX KEYMaintenance Battery Pack Removal and Preparation for RecyclingBatteries Page See Back page for Parts Ordering Instructions Parts List Craftsman 1/2 in., 19.2 Volt Cordless DRILL-DRIVER Model noGet it fixed, at your home or ours Operators Manual ONE Year Full Warranty on Craftsman Tool Model Battery Pack Charger Electrical SafetyPersonal Safety Work AreaCauses and Operator Prevention of Kickback Laser Guide Warnings Safety Rules for Charger Symbols Service Product Specifications Spindle Lock Button Laser Guide RIPAssembly Installing Battery Pack Latches Battery PackAttaching Blade Spindle Lock Screw To Loosen Installing Edge GuideRemoving Blade To Tighten EdgeCharging the Battery Pack Charging a Cool Battery PackApplications Charging a HOT Battery Pack Kickback Incorrect SupportCorrect Support Kickback SAW Blades Lower Blade Guard Is in UP Position When Making a CUTSwitch Trigger Blade Exposed on Underside of Workpiece Blade Guard SystemDepth Base Assembly Tighten Adjusting Blade DepthUsing the Laser Guide Adjustment KnobOperating the SAW Wrong Correct WR ONGCross CUTTING/RIP Cutting Bevel Cutting To Adjust Bevel SettingBevel Adjustment Knob Scale Blade Guide Notch Bevel ScaleTo Adjust Positive 0 Bevel Stop Positive 0 Bevel StopTo Check Positive 0 Bevel Stop Pocket Cutting AdjustmentsAdjusting the Laser Pocket CUT Lower Blade GuardGeneral Maintenance LubricationReplacing Laser Guide Batteries Accessories Battery Pack Removal Preparation for RecyclingBatteries 3733 Number ModelCraftsman 19.2 Volt Cordless Trim SAW Model Number KEY Part Number Description QTYVolt Reciprocating Saw Variable Speed Table of Contents General Safety Rules Specific Safety Rules Safety Rules for Charger Symbols Service Volts DC Toolless Blade Clamp SwitchKnow Your Reciprocating SAW HEX KEY HolderAssembly Battery Pack Shown Charger To Remove To Remove / Attach Battery PackBattery Port Battery Pack Latch To Install SAW Blade To AttachGeneral Cutting Base Shoe AssemblyTo Change Positions of Base Assembly PivotPlunge Cutting Metal CuttingMaintenance Blade Types Length Craftsman 19.2 Volt Reciprocating SAW Model no See Back page for Parts Ordering InstructionsGet it fixed, at your home or ours Volt Fluorescent Light Warranty General Safety Rules Specific Safety Rules Important Safety Instructions for Charger Symbols Operation Switch Maintenance Battery Pack Removal and Preparation for Recycling Page Get it fixed, at your home or ours