Sears 315.11485 manual Maintenance

Page 61

MAINTENANCE

WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage.

WARNING: Always wear safety goggles or safety glasses with side shields when using compressed air to clean tools. If the operation is dusty, also wear a dust mask.

WARNING: To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. Chemi- cals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center.

BATTERIES

The battery pack for this tool is equipped with nickel-cad- mium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing.

The batteries in this tool have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.

To obtain the longest possible battery life, we suggest the following:

nRemove the battery pack from the charger once it is fully charged and ready for use.

nStore the battery pack where the temperatures is be- low 80°F.

nStore battery packs in a "discharged" condition.

BATTERY PACK REMOVAL AND

PREPARATION FOR RECYCLING

To preserve natural resources, please recycle or dispose of batteries

properly.

This product contains nickel-cadmium

batteries. Local, state or federal

laws may prohibit disposal of nickel- cadmium batteries in ordinary trash.

Consult your local waste authority for information regarding available recycling and/or disposal options.

WARNING: Upon removal, cover the battery pack’s terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

15

Image 61
Contents Operators Manual Warranty Table of ContentsIntroduction Electrical Safety General Safety RulesPersonal Safety Work AreaService Specific Safety RulesRules for Battery Tools Additional Rules for Safe OperationSafety Instructions for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Specifications Features Instructions UnpackingPacking List Charging Battery Pack Battery PackInformation for Recharging Cool Battery Pack OperationTo Remove Battery Pack To Install Battery PackTWO-SPEED Gear Train Reversible Switch Forward TriggerDrill BIT Lock Tighten Chuck BodyAdjustable Torque Clutch Installing BitsTo Adjust Torque Removing BitsScrewdriver BIT BIT Storage Area DrillingTo Retighten a Loose Chuck Chuck RemovalMallet Chuck Jaws Mallet HEX KEYBattery Pack Removal and Preparation for Recycling MaintenanceBatteries Page Craftsman 1/2 in., 19.2 Volt Cordless DRILL-DRIVER Model no See Back page for Parts Ordering Instructions Parts ListGet it fixed, at your home or ours Operators Manual ONE Year Full Warranty on Craftsman Tool Personal Safety Electrical SafetyModel Battery Pack Charger Work AreaCauses and Operator Prevention of Kickback Laser Guide Warnings Safety Rules for Charger Symbols Service Spindle Lock Button Laser Guide RIP Product SpecificationsAssembly Latches Battery Pack Installing Battery PackAttaching Blade Removing Blade Installing Edge GuideSpindle Lock Screw To Loosen To Tighten EdgeCharging a Cool Battery Pack Charging the Battery PackApplications Charging a HOT Battery Pack Incorrect Support KickbackCorrect Support Kickback Switch Trigger Blade Exposed on Underside of Workpiece Lower Blade Guard Is in UP Position When Making a CUTSAW Blades Blade Guard SystemUsing the Laser Guide Adjusting Blade DepthDepth Base Assembly Tighten Adjustment KnobWrong Correct WR ONG Operating the SAWCross CUTTING/RIP Cutting Bevel Adjustment Knob Scale Blade Guide Notch To Adjust Bevel SettingBevel Cutting Bevel ScalePositive 0 Bevel Stop To Adjust Positive 0 Bevel StopTo Check Positive 0 Bevel Stop Adjusting the Laser AdjustmentsPocket Cutting Pocket CUT Lower Blade GuardLubrication General MaintenanceReplacing Laser Guide Batteries Battery Pack Removal Preparation for Recycling AccessoriesBatteries Number Model 3733KEY Part Number Description QTY Craftsman 19.2 Volt Cordless Trim SAW Model NumberVolt Reciprocating Saw Variable Speed Table of Contents General Safety Rules Specific Safety Rules Safety Rules for Charger Symbols Service Volts DC Know Your Reciprocating SAW SwitchToolless Blade Clamp HEX KEY HolderAssembly Battery Pack Shown Charger Battery Port Battery Pack Latch To Install SAW Blade To Remove / Attach Battery PackTo Remove To AttachTo Change Positions of Base Assembly Base Shoe AssemblyGeneral Cutting PivotMetal Cutting Plunge CuttingMaintenance Blade Types Length See Back page for Parts Ordering Instructions Craftsman 19.2 Volt Reciprocating SAW Model noGet it fixed, at your home or ours Volt Fluorescent Light Warranty General Safety Rules Specific Safety Rules Important Safety Instructions for Charger Symbols Operation Switch Maintenance Battery Pack Removal and Preparation for Recycling Page Get it fixed, at your home or ours