Sears 315.11485 manual Switch

Page 72

OPERATION

LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK:

Red LED on = Fast charging mode.

Green LED on = Fully charged and in trickle charge mode.

Green LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack is out of or below normal temperature range.

Yellow and Green LEDs on = Deeply discharged or defective battery pack.

No LED on = Defective charger or battery pack.

CAUTION: To prevent damage to battery pack, remove battery pack from charger immediately if no LED comes on. Return battery pack and charger to your nearest Sears Service Center for checking or replacing. Also, if you are removing battery pack from charger and no LEDs are on, return both battery pack and charger to your nearest Sears Service Center. Do not insert another battery pack into charger. A damaged charger may damage a battery pack.

TO INSTALL OR REMOVE BATTERY PACK

See Figure 2.

Use only the recommended battery pack with your light.

WARNING: Do not install battery pack to your light until you have read and understood all precautions and operating instructions in the manual and printed on battery pack and charger.

Orient battery pack so that raised rib on battery pack aligns with groove inside light. Battery pack is de- signed to fit only one way into light handle.

Insert battery pack, making sure latches on each side of battery pack snap into place and battery pack is secure in light before use.

CAUTION: When placing battery pack in your light, be sure raised rib on battery pack aligns with groove inside light handle and latches snap into place properly. Improper assembly of battery pack can cause damage to internal components.

To remove battery pack, locate latches on end of battery pack and depress to release battery pack from your light.

SWITCH

See Figure 3.

To turn light on and off, depress switch trigger.

SWITCH

Fig. 3

HANGING / STORAGE FEATURE

See Figure 4.

On top of the housing is a hook in which you can use to hang the light up. This is a good feature for storing light when not in use and also to keep light out of the reach of children. To use, simply lift up on hook.

TO

HANGER

RAISE

 

LATCHES

TO

LOWER

BATTERY PACK

Fig. 2

Fig 4

8

Image 72
Contents Operators Manual Table of Contents WarrantyIntroduction General Safety Rules Electrical SafetyPersonal Safety Work AreaSpecific Safety Rules ServiceRules for Battery Tools Additional Rules for Safe OperationSafety Instructions for Charger Symbols Symbol Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Specifications Features Unpacking InstructionsPacking List Battery Pack Charging Battery PackInformation for Recharging Cool Battery Pack OperationTo Install Battery Pack To Remove Battery PackTWO-SPEED Gear Train Switch Forward Trigger ReversibleDrill BIT Lock Tighten Chuck BodyInstalling Bits Adjustable Torque ClutchTo Adjust Torque Removing BitsDrilling Screwdriver BIT BIT Storage AreaChuck Removal To Retighten a Loose ChuckMallet Chuck Jaws Mallet HEX KEYMaintenance Battery Pack Removal and Preparation for RecyclingBatteries Page See Back page for Parts Ordering Instructions Parts List Craftsman 1/2 in., 19.2 Volt Cordless DRILL-DRIVER Model noGet it fixed, at your home or ours Operators Manual ONE Year Full Warranty on Craftsman Tool Electrical Safety Personal SafetyModel Battery Pack Charger Work AreaCauses and Operator Prevention of Kickback Laser Guide Warnings Safety Rules for Charger Symbols Service Product Specifications Spindle Lock Button Laser Guide RIPAssembly Installing Battery Pack Latches Battery PackAttaching Blade Installing Edge Guide Removing BladeSpindle Lock Screw To Loosen To Tighten EdgeCharging the Battery Pack Charging a Cool Battery PackApplications Charging a HOT Battery Pack Kickback Incorrect SupportCorrect Support Kickback Lower Blade Guard Is in UP Position When Making a CUT Switch Trigger Blade Exposed on Underside of WorkpieceSAW Blades Blade Guard SystemAdjusting Blade Depth Using the Laser GuideDepth Base Assembly Tighten Adjustment KnobOperating the SAW Wrong Correct WR ONGCross CUTTING/RIP Cutting To Adjust Bevel Setting Bevel Adjustment Knob Scale Blade Guide NotchBevel Cutting Bevel ScaleTo Adjust Positive 0 Bevel Stop Positive 0 Bevel StopTo Check Positive 0 Bevel Stop Adjustments Adjusting the LaserPocket Cutting Pocket CUT Lower Blade GuardGeneral Maintenance LubricationReplacing Laser Guide Batteries Accessories Battery Pack Removal Preparation for RecyclingBatteries 3733 Number ModelCraftsman 19.2 Volt Cordless Trim SAW Model Number KEY Part Number Description QTYVolt Reciprocating Saw Variable Speed Table of Contents General Safety Rules Specific Safety Rules Safety Rules for Charger Symbols Service Volts DC Switch Know Your Reciprocating SAWToolless Blade Clamp HEX KEY HolderAssembly Battery Pack Shown Charger To Remove / Attach Battery Pack Battery Port Battery Pack Latch To Install SAW BladeTo Remove To AttachBase Shoe Assembly To Change Positions of Base AssemblyGeneral Cutting PivotPlunge Cutting Metal CuttingMaintenance Blade Types Length Craftsman 19.2 Volt Reciprocating SAW Model no See Back page for Parts Ordering InstructionsGet it fixed, at your home or ours Volt Fluorescent Light Warranty General Safety Rules Specific Safety Rules Important Safety Instructions for Charger Symbols Operation Switch Maintenance Battery Pack Removal and Preparation for Recycling Page Get it fixed, at your home or ours