Sears 113.244530 owner manual Troubleshooting, Wiring diagram, Probable Cause, Remedy

Page 20

troubleshooting

WARNING: For your own safety, Push on-off knob "OFF", lock-out switch and remove plug from power outlet before readjusting or aligning your band saw.

TROUBLE

Motor will not run.

Blade does not run in the approximate center of the upper wheel.

PROBABLE CAUSE

1.Damaged On-Off switch. Damaged power cord.

2.Motor damaged.

1. Not tracking properly.

REMEDY

1.Replace damaged parts before using Band Saw again.

. Consult Sears Service. Any attempt to repair this motor may create a HAZARD unless repair

is done by a qualified service technician. Repair service is available at your nearest Sears Store.

1.Adjust tracking, see Assembly Section, "Tracking the Blade."

Band Saw slows down when cutting.

Blades breaking.

Saw is noisy when running.

1.Cutting too small a radius.

2.Dull blade.

1. Too much tension.

,Kink in blade caused by cutting too small a radius or turning the material too fast when cutting.

1. Too much blade tension

1.Stop feeding, and back up the material slightly, until the band saw speeds up.

2.Replace blade.

1.Adjust tension. See Assembly section "Tensioning The Blade."

2.Use correct cutting technique. See Basic Band Saw Operation Section.

1.Adjust blade tension. See Assembly section "Tensioning The Blade."

Blade will not cut straight.

Blade guides will not stay in position

Motor stops during cut

2.Blade guides and back-up bearings are in contact with the blade.

1.Blade guides and bearings not properly adjusted.

2.Worn or damaged blade.

,Patch on blade guide threads has deteriorated

allowing them to rotate with the blade.

1.Aggressive feeding causes Current Protector to shut motor off.

2.Adjust upper and lower blade guides and bearings. See assembly section "Adjusting the Blade Guides and Back-up Bearing."

1.Adjust upper and lower blade guides and bearings. See Assembly section "Adjusting Guides and Back-up Bearing."

2.Replace blade.

1.Replace blade guides.

1.Turn machine "OFF" and then back "ON" to continue cutting.

2.Slow down the feed rate of material into blade.

wiring diagram

WARNING: To avoid electrocution or fire, repair

electricals only with recommended service

parts, and reassemble exactly as originally received when new.

Green

 

 

Leads

e

Sensor

 

 

IIIIIi

 

White,

 

Black

._witch

20

M+ M-

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 9ARS Variable Speed 10-1NCH Band SAWSafety Instructions for Band Saw Full ONE Year Warranty on Craftsman Band SAWBefore Using the SAW When Installing or Moving the SAWPlan your work Inspect your workpieceLock the switch Unplug the saw Glossary of termsBefore Leaving the SAW FPMMotor specifications and electrical requirements Connecting to Power Supply OutletFire hazard and may also create a shock hazard FeetUnpacking and checking contents Assembly Table of Loose Parts QTYMounting Band SAW to Workbench Clamping Bandsaw to WorkbenchInstalling the Table Tonn,on I JInstalling the Blade Installing bladeWith one hand on the knob and the other on Lock and unplug before making any adjust MentsTensioning the Blade Tracking the Blade Adjusting the Blade Guides and BACK-UP BearingPadlock, and unplug before making any adjust- ments Final Table Assembly Aligning the Table Square To the BladeCover l Open. Thrown blades can cause injuryInstalling the Hose Clip Getting to know your band saw Upper slide lock knob... The upper blade guideON-OFF Knoi Tended Until IT has Come to a Complete StopBasic Saw Operations Choice of Blade and SpeedBlade Type and Approximate Speed for Cutting Material Speed BladeWhenever SAW is Running Enough to cause a severe injuryMaintenance Basic band saw operationTires GeneralMaintenance Sears recommends the following accessoriesTroubleshooting Wiring diagramTrouble Probable CauseRepair parts Always order by Part Number- Not by Key NumberLO €4 TO IJU Inch Band Saw Partnumber Partdescription Model Number Name of ItemVariable Speed
Top Page Image Contents