Patton electronic 4520 user manual SmartNode 4110 Series power input connectors

Page 17

SmartNode 4520 & 4110 Series User Manual

1 • General information

 

 

The port combinations are indicated in the extension of the model code. The products the following model code conventions apply:

JS stands for FXS ports

JO stands for FXO ports

UI stands for integrated universal input power supply (see figure 6)

EUI stands for external universal input power supply (see figure 6)

For example, the model code SN4116/4JS2JO/EUI describes a SmartNode configured as follows:

4 FXS ports

2 FXO ports

External power supply

Note For a complete listing of available models, refer to the SmartNode

VoIP page at http://www.patton.com/voip/.

Figure 6. SmartNode 4110 Series power input connectors

SmartNode Series VoIP routers overview

17

Image 17
Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling Structure About this guideAudience Safety when working with electricity PrecautionsPreventing electrostatic discharge damage General conventions Typographical conventions used in this documentGeneral observations General information Chapter contentsSmartNode Router SmartNode 4524 shown SmartNode Series VoIP routers overviewExamples of SN4520 Series rear panels SmartNode 4520 Series routerSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels Examples of SN4110 Series rear panels SmartNode 4110 Series routerSmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview SIP and H.323 terminal and Pstn gateways IntroductionApplications for SmartNode 4110 Series Application-Analog line extension over IP Application-ITSP dial-in accessApplication-Enterprise campus BRI to FXS telephony extension Application-Private line automatic ringdown PlarApplication-PBX toll bypass gateway Applications for SmartNode 4520 SeriesHome office networking Application-SOHO off-premise extensionSingle-phone access Application-Single-phone Pstn and VoIP accessHardware installation Create a network diagram see section Network information on Planning the installationTask Verified by Date Installation checklistSite log Power sourceNetwork information IP related informationConnecting cables Installing the gateway routerLocation and mounting requirements Mounting the gateway routerAnalog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Connect with the serial interface Configure IP addressPower connection and default configuration Changing the IP address LoginConnect the SmartNode to the network Load configurationStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory configurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Examples of SN4520 Series front panels Status LEDsExamples of SN4110 Series front panels LED Contacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Compliance Authorized European Representative ComplianceCE Declaration of Conformity Industry Canada Notice FXO Ports Radio and TV Interference FCC PartFCC Part 68 Acta Statement FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Voice connectivity Voice processing signalling dependentConnectivity Fax and modem supportVoice routing-session router Voice signallingIP services Weight and power dissipation DimensionsManagement Operating environmentAC version Power supplyIdentification of the SmartNode devices via Snmp Identification of the SmartNode devices via Snmp Appendix C Cabling Serial console Connecting a serial terminalEthernet cross-over Ethernet 10Base-T and 100Base-TEthernet straight-through Analog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketAppendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portFXO port FXS portAppendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist
Related manuals
Manual 90 pages 10.74 Kb Manual 66 pages 3.94 Kb