Patton electronic 4110, 4520 user manual About this guide, Audience, Structure

Page 6

About this guide

This guide describes the SmartNode 4110 and 4520 Series hardware, installation and basic configuration. For detailed software configuration information refer to the SmartWare Software Configuration Guide and the avail- able Configuration Notes.

Audience

This guide is intended for the following users:

Operators

Installers

Maintenance technicians

Structure

This guide contains the following chapters and appendices:

Chapter 1 on page 10 provides information about router features and capabilities

Chapter 2 on page 20 contains an overview describing router operation and applications

Chapter 3 on page 27 provides quick start hardware installation procedures

Chapter 4 on page 38 describes getting started with the SmartNode router

Chapter 5 on page 47 contains definitions for the LED status indicators

Chapter 6 on page 51 contains information on contacting Patton technical support for assistance

Appendix B on page 58 contains specifications for the routers

Appendix C on page 64 provides cable recommendations

Appendix D on page 70 describes the router’s ports and pin-outs

Appendix E on page 73 lists the factory configuration settings for SmartNode 4110 Series devices

Appendix F on page 75 lists the factory configuration settings for SmartNode 4520 Series devices

Appendix G on page 77 lists the tasks for installing a SmartNode 4520 or 4110 Series router

For best results, read the contents of this guide before you install the router.

6

Image 6
Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling About this guide AudienceStructure Precautions Safety when working with electricityPreventing electrostatic discharge damage Typographical conventions used in this document General observationsGeneral conventions Chapter contents General informationSmartNode Series VoIP routers overview SmartNode Router SmartNode 4524 shownSmartNode 4520 Series router Examples of SN4520 Series rear panelsSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels SmartNode 4110 Series router Examples of SN4110 Series rear panelsSmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview Introduction Applications for SmartNode 4110 SeriesSIP and H.323 terminal and Pstn gateways Application-ITSP dial-in access Application-Analog line extension over IPApplication-Private line automatic ringdown Plar Application-Enterprise campus BRI to FXS telephony extensionApplications for SmartNode 4520 Series Application-PBX toll bypass gatewayApplication-SOHO off-premise extension Home office networkingApplication-Single-phone Pstn and VoIP access Single-phone accessHardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist Task Verified by DateNetwork information Power sourceSite log IP related informationLocation and mounting requirements Installing the gateway routerConnecting cables Mounting the gateway routerAnalog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Configure IP address Power connection and default configurationConnect with the serial interface Login Changing the IP addressLoad configuration Connect the SmartNode to the networkBootloader Start BootloaderStart-up with factory configuration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkLEDs status and monitoring Status LEDs Examples of SN4520 Series front panelsExamples of SN4110 Series front panels LED Contacting Patton for assistance Warranty coverage Contact informationReturn for credit policy RMA numbersAppendix a Compliance Compliance CE Declaration of ConformityAuthorized European Representative Radio and TV Interference FCC Part FCC Part 68 Acta Statement FXO PortsIndustry Canada Notice FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Connectivity Voice processing signalling dependentVoice connectivity Fax and modem supportVoice signalling IP servicesVoice routing-session router Management DimensionsWeight and power dissipation Operating environmentPower supply Identification of the SmartNode devices via SnmpAC version Identification of the SmartNode devices via Snmp Appendix C Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet cross-overEthernet straight-through Connecting an FXS device Analog FXSConnecting to an FXO line socket Analog FXOAppendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T portFXS port FXO portAppendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist
Related manuals
Manual 90 pages 10.74 Kb Manual 66 pages 3.94 Kb