Patton electronic 4520 Voice connectivity, Connectivity, Voice processing signalling dependent

Page 59

SmartNode 4520 & 4110 Series User Manual	B • Specifications

DSP

One or two 4-channel DSPs

Voice connectivity

2-wire Loopstart, RJ-11/12 Short haul loop 1.1 km @3REN EuroPOTS (ETSI EG201 188)

Programmable AC impedance, feeding, and ring voltage; On-Hook Voltage 29VDC

Caller-ID Type-1/2 FSK and ITU V.23/Bell 202 generation

Connectivity

2 10/100 Full Duplex/Autosensing Ethernet RJ-45

Voice processing (signalling dependent)

Voice codes:

•G.711 A-Law/ -Law (64 kbps)

•G.726 (ADPCM 40, 32, 24, 16 kpbs)

•G.723.1 (5.3 or 6.3 kbps)

•G.729ab (8 kbps)

•Transparent pass through

G.168 echo cancellation

8 parallel voice connections DTMF detection and generation Carrier tone detection and generation Silence suppression and comfort noise Configurable dejitter buffer Configurable tones (dial, ringing, busy) Configurable transmit packet length RTP/RTCP (RFC 1889)

Fax and modem support

G.711 transparent FAX

Fax over IP (FoIP)

T.38 Fax relay (9.6 k, 14.4 k)

DSP

59

Image 59

Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling Structure About this guideAudience Safety when working with electricity PrecautionsPreventing electrostatic discharge damage General conventions Typographical conventions used in this documentGeneral observations General information Chapter contentsSmartNode Router SmartNode 4524 shown SmartNode Series VoIP routers overviewExamples of SN4520 Series rear panels SmartNode 4520 Series routerSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels Examples of SN4110 Series rear panels SmartNode 4110 Series routerSmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview SIP and H.323 terminal and Pstn gateways IntroductionApplications for SmartNode 4110 Series Application-Analog line extension over IP Application-ITSP dial-in accessApplication-Enterprise campus BRI to FXS telephony extension Application-Private line automatic ringdown PlarApplication-PBX toll bypass gateway Applications for SmartNode 4520 SeriesHome office networking Application-SOHO off-premise extensionSingle-phone access Application-Single-phone Pstn and VoIP accessHardware installation Create a network diagram see section Network information on Planning the installationTask Verified by Date Installation checklistIP related information Power sourceSite log Network informationMounting the gateway router Installing the gateway routerConnecting cables Location and mounting requirementsAnalog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Connect with the serial interface Configure IP addressPower connection and default configuration Changing the IP address LoginConnect the SmartNode to the network Load configurationStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory configurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Examples of SN4520 Series front panels Status LEDsExamples of SN4110 Series front panels LED Contacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Compliance Authorized European Representative ComplianceCE Declaration of Conformity Industry Canada Notice FXO Ports Radio and TV Interference FCC PartFCC Part 68 Acta Statement FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Fax and modem support Voice processing signalling dependentVoice connectivity ConnectivityVoice routing-session router Voice signallingIP services Operating environment DimensionsWeight and power dissipation ManagementAC version Power supplyIdentification of the SmartNode devices via Snmp Identification of the SmartNode devices via Snmp Appendix C Cabling Serial console Connecting a serial terminalEthernet cross-over Ethernet 10Base-T and 100Base-TEthernet straight-through Analog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketAppendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portFXO port FXS portAppendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist

Related manuals

Manual 90 pages 10.74 Kb

Manual 66 pages 3.94 Kb