Patton electronic 4110, 4520 user manual Appendix D Port pin-outs, Chapter contents

Page 70

Appendix D Port pin-outs

 

Chapter contents

 

Introduction

71

Console port

71

Ethernet 10Base-T and 100Base-T port

71

FXS port

72

FXO port

72

70

Page 69 Page 71
Image 70
Page 69 Page 71
Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling Audience About this guideStructure Precautions Safety when working with electricityPreventing electrostatic discharge damage General observations Typographical conventions used in this documentGeneral conventions Chapter contents General informationSmartNode Series VoIP routers overview SmartNode Router SmartNode 4524 shownSmartNode 4520 Series router Examples of SN4520 Series rear panelsSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels SmartNode 4110 Series router Examples of SN4110 Series rear panelsSmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview Applications for SmartNode 4110 Series IntroductionSIP and H.323 terminal and Pstn gateways Application-ITSP dial-in access Application-Analog line extension over IPApplication-Private line automatic ringdown Plar Application-Enterprise campus BRI to FXS telephony extensionApplications for SmartNode 4520 Series Application-PBX toll bypass gatewayApplication-SOHO off-premise extension Home office networkingApplication-Single-phone Pstn and VoIP access Single-phone accessHardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist Task Verified by DateNetwork information Power sourceSite log IP related informationLocation and mounting requirements Installing the gateway routerConnecting cables Mounting the gateway routerAnalog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default configuration Configure IP addressConnect with the serial interface Login Changing the IP addressLoad configuration Connect the SmartNode to the networkBootloader Start BootloaderStart-up with factory configuration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkLEDs status and monitoring Status LEDs Examples of SN4520 Series front panelsExamples of SN4110 Series front panels LED Contacting Patton for assistance Warranty coverage Contact informationReturn for credit policy RMA numbersAppendix a Compliance CE Declaration of Conformity ComplianceAuthorized European Representative FCC Part 68 Acta Statement FXO Ports Radio and TV Interference FCC PartIndustry Canada Notice FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Connectivity Voice processing signalling dependentVoice connectivity Fax and modem supportIP services Voice signallingVoice routing-session router Management DimensionsWeight and power dissipation Operating environmentIdentification of the SmartNode devices via Snmp Power supplyAC version Identification of the SmartNode devices via Snmp Appendix C Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet cross-overEthernet straight-through Connecting an FXS device Analog FXSConnecting to an FXO line socket Analog FXOAppendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T portFXS port FXO portAppendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist
Related manuals
Manual 90 pages 10.74 Kb Manual 66 pages 3.94 Kb
Top Page Image Contents