Patton electronic 4110 Power supply, Identification of the SmartNode devices via Snmp, AC version

Page 62

SmartNode 4520 & 4110 Series User Manual

B • Specifications

 

 

Power supply

The terminal block header to which the wires are secured pro-

vides the disconnect for the SmartNode. Take proper measures CAUTION to ensure that it is not permanently fastened to the receptacle

mounted on the chassis.

AC version

Internal power supply 100–240 VAC, 50/60 Hz, 200 mA

DC version 12 VDC, 1.25 A

Note Power is to be provided by an agency-approved external SELV source which provides reinforced insulation from the AC mains power and where the DC connector is the disconnect device. The source must have a rating of

12 VDC, 1.25 A.

Identification of the SmartNode devices via SNMP

All SmartNode devices have assigned sysObjectID (.iso.org.dod.internet.mgmt.mib-2.system.sysObjectID) numbers (see table 11).

Table 11. SmartNode Models and their Unique sysObjectID

SmartNode Model

SysObjectID

 

 

SN4112-JS

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.5

 

1.3.6.1.4.1.1768.2.4.5.5

SN4112-JO

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.19

 

1.3.6.1.4.1.1768.2.4.5.19

 

 

SN4114-JS

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.6

 

1.3.6.1.4.1.1768.2.4.5.6

SN4114-JO

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.20

 

1.3.6.1.4.1.1768.2.4.5.20

 

 

SN4114-2JS2JO

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.12

 

1.3.6.1.4.1.1768.2.4.5.12

SN4116-JS

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.7

 

1.3.6.1.4.1.1768.2.4.5.7

 

 

SN4116-JO

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.21

 

1.3.6.1.4.1.1768.2.4.5.21

SN4116-4JS2JO

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.13

 

1.3.6.1.4.1.1768.2.4.5.13

 

 

SN4118-JS

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.8

 

1.3.6.1.4.1.1768.2.4.5.8

SN4118-JO

.iso.org.dod.internet.private.enterprises.patton.products.sn4xxx.22

 

1.3.6.1.4.1.1768.2.4.5.22

 

 

Power supply

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling Structure About this guideAudience Precautions Safety when working with electricityPreventing electrostatic discharge damage General conventions Typographical conventions used in this documentGeneral observations Chapter contents General informationSmartNode Series VoIP routers overview SmartNode Router SmartNode 4524 shownSmartNode 4520 Series router Examples of SN4520 Series rear panelsSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels SmartNode 4110 Series router Examples of SN4110 Series rear panelsSmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview SIP and H.323 terminal and Pstn gateways IntroductionApplications for SmartNode 4110 Series Application-ITSP dial-in access Application-Analog line extension over IPApplication-Private line automatic ringdown Plar Application-Enterprise campus BRI to FXS telephony extensionApplications for SmartNode 4520 Series Application-PBX toll bypass gatewayApplication-SOHO off-premise extension Home office networkingApplication-Single-phone Pstn and VoIP access Single-phone accessHardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist Task Verified by DateNetwork information Power sourceSite log IP related informationLocation and mounting requirements Installing the gateway routerConnecting cables Mounting the gateway routerAnalog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Connect with the serial interface Configure IP addressPower connection and default configuration Login Changing the IP addressLoad configuration Connect the SmartNode to the networkBootloader Start BootloaderStart-up with factory configuration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkLEDs status and monitoring Status LEDs Examples of SN4520 Series front panelsExamples of SN4110 Series front panels LED Contacting Patton for assistance Warranty coverage Contact informationReturn for credit policy RMA numbersAppendix a Compliance Authorized European Representative ComplianceCE Declaration of Conformity Industry Canada Notice FXO Ports Radio and TV Interference FCC PartFCC Part 68 Acta Statement FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Connectivity Voice processing signalling dependentVoice connectivity Fax and modem supportVoice routing-session router Voice signallingIP services Management DimensionsWeight and power dissipation Operating environmentAC version Power supplyIdentification of the SmartNode devices via Snmp Identification of the SmartNode devices via Snmp Appendix C Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet cross-overEthernet straight-through Connecting an FXS device Analog FXSConnecting to an FXO line socket Analog FXOAppendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T portFXS port FXO portAppendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist
Related manuals
Manual 90 pages 10.74 Kb Manual 66 pages 3.94 Kb
Top Page Image Contents