Patton electronic 4520, 4110 user manual Ethernet straight-through

Page 67

SmartNode 4520 & 4110 Series User Manual

C • Cabling

 

 

 

 

 

 

 

 

Figure 31. Ethernet straight-through

Ethernet 10Base-T and 100Base-T

67

Page 66 Page 68
Image 67
Page 66 Page 68
Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling Audience About this guideStructure Safety when working with electricity PrecautionsPreventing electrostatic discharge damage General observations Typographical conventions used in this documentGeneral conventions General information Chapter contentsSmartNode Router SmartNode 4524 shown SmartNode Series VoIP routers overviewExamples of SN4520 Series rear panels SmartNode 4520 Series routerSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels Examples of SN4110 Series rear panels SmartNode 4110 Series routerSmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview Applications for SmartNode 4110 Series IntroductionSIP and H.323 terminal and Pstn gateways Application-Analog line extension over IP Application-ITSP dial-in accessApplication-Enterprise campus BRI to FXS telephony extension Application-Private line automatic ringdown PlarApplication-PBX toll bypass gateway Applications for SmartNode 4520 SeriesHome office networking Application-SOHO off-premise extensionSingle-phone access Application-Single-phone Pstn and VoIP accessHardware installation Create a network diagram see section Network information on Planning the installationTask Verified by Date Installation checklistIP related information Power sourceSite log Network informationMounting the gateway router Installing the gateway routerConnecting cables Location and mounting requirementsAnalog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default configuration Configure IP addressConnect with the serial interface Changing the IP address LoginConnect the SmartNode to the network Load configurationStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory configurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Examples of SN4520 Series front panels Status LEDsExamples of SN4110 Series front panels LED Contacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Compliance CE Declaration of Conformity ComplianceAuthorized European Representative FCC Part 68 Acta Statement FXO Ports Radio and TV Interference FCC PartIndustry Canada Notice FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Fax and modem support Voice processing signalling dependentVoice connectivity ConnectivityIP services Voice signallingVoice routing-session router Operating environment DimensionsWeight and power dissipation ManagementIdentification of the SmartNode devices via Snmp Power supplyAC version Identification of the SmartNode devices via Snmp Appendix C Cabling Serial console Connecting a serial terminalEthernet cross-over Ethernet 10Base-T and 100Base-TEthernet straight-through Analog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketAppendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portFXO port FXS portAppendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist
Related manuals
Manual 90 pages 10.74 Kb Manual 66 pages 3.94 Kb
Top Page Image Contents