Patton electronic 4520, 4110 user manual Start Bootloader

Page 43

SmartNode 4520 & 4110 Series User Manual	4 • Getting started with the SmartNode

172.16.1.99(if-ip)[eth0]#

After the SmartNode has been rebooted the new start up configuration will be activated.

172.16.1.99(if-ip)[eth0]#reload Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'? Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes The system is going down

Bootloader

The bootloader ensures that basic operations, network access, and downloads are possible in case of interrupted or corrupted application image downloads. It also offers console access to the Bootloader and the capability for downloading application images (e.g. SmartWare) via the serial link of the console.

Start Bootloader

To start the Bootloader, power on the SmartNode while pressing the reset button. Open a Telnet session to the SmartNode via one of the Ethernet interfaces, or open a CLI session via the console port (if available on the SmartNode). The login display will appear. Using the credentials admin / patton, log in to the SmartNode. The following prompt will be displayed:

RedBoot>

Type help to display an overview of the available commands.

Bootloader

43

Image 43

Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling Audience About this guideStructure Safety when working with electricity PrecautionsPreventing electrostatic discharge damage General observations Typographical conventions used in this documentGeneral conventions General information Chapter contentsSmartNode Router SmartNode 4524 shown SmartNode Series VoIP routers overviewExamples of SN4520 Series rear panels SmartNode 4520 Series routerSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels Examples of SN4110 Series rear panels SmartNode 4110 Series routerSmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview Applications for SmartNode 4110 Series IntroductionSIP and H.323 terminal and Pstn gateways Application-Analog line extension over IP Application-ITSP dial-in accessApplication-Enterprise campus BRI to FXS telephony extension Application-Private line automatic ringdown PlarApplication-PBX toll bypass gateway Applications for SmartNode 4520 SeriesHome office networking Application-SOHO off-premise extensionSingle-phone access Application-Single-phone Pstn and VoIP accessHardware installation Create a network diagram see section Network information on Planning the installationTask Verified by Date Installation checklistIP related information Power sourceSite log Network informationMounting the gateway router Installing the gateway routerConnecting cables Location and mounting requirementsAnalog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default configuration Configure IP addressConnect with the serial interface Changing the IP address LoginConnect the SmartNode to the network Load configurationStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory configurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Examples of SN4520 Series front panels Status LEDsExamples of SN4110 Series front panels LED Contacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Compliance CE Declaration of Conformity ComplianceAuthorized European Representative FCC Part 68 Acta Statement FXO Ports Radio and TV Interference FCC PartIndustry Canada Notice FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Fax and modem support Voice processing signalling dependentVoice connectivity ConnectivityIP services Voice signallingVoice routing-session router Operating environment DimensionsWeight and power dissipation ManagementIdentification of the SmartNode devices via Snmp Power supplyAC version Identification of the SmartNode devices via Snmp Appendix C Cabling Serial console Connecting a serial terminalEthernet cross-over Ethernet 10Base-T and 100Base-TEthernet straight-through Analog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketAppendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portFXO port FXS portAppendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist

Related manuals

Manual 90 pages 10.74 Kb

Manual 66 pages 3.94 Kb