Hobart 3225DX manual Servicing Fuel And Lubrication Systems, To change oil and filter

Page 32

7-4. Servicing Fuel And Lubrication Systems

 

Y Stop engine and let cool.

 

1

Oil Filter

 

2

Oil Drain Plug

 

3

Oil Fill Cap

 

4

Primary Fuel Filter (Fuel/

 

 

Water Separator)

 

5

Petcock

 

6

Secondary Fuel Filter

 

7

Fuel Shutoff Valve

 

8

Fuel Line

 

9

Sludge Drain Plug

 

To change oil and filter:

 

See engine manual.

9

To drain water from fuel system:

 

 

 

Open primary fuel filter petcock and

 

drain water into metal container.

 

Close petcock when water-free fuel

 

flows.

 

To replace primary fuel filter:

 

Close shutoff valve and turn filter

 

counterclockwise. Remove filter.

 

Apply thin coat of fuel to gasket on

 

new filter. Install new filter and turn

 

clockwise. Open shutoff valve.

 

Bleed air from fuel system accord-

 

ing to engine manual.

 

Inspect fuel line, and replace if

 

cracked or worn.

 

To replace secondary fuel filter:

 

See engine manual.

 

To drain sludge from fuel tank:

3

1 6

2

7

4

Valve Open

8

5

Put metal container under drain, and remove sludge drain plug. Re- install plug when done.

YAfter servicing, start engine and check for fuel leaks.

YStop engine, tighten connec- tions as necessary, and wipe up spilled fuel.

Close doors.

Tools Needed:

7/16, 11/16 in

Ref. ST-801 739 / Ref. ST-188 449

OM-130 098 Page 28

Page 31 Page 33
Image 32
Page 31 Page 33
Contents OM-130 ProcessesVisit our website at AugustFrom Hobart to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill ARC Rays can burn eyes and skinEngine Hazards Battery Explosion can Blind Moving Parts can cause injuryEngine Exhaust Gases can kill Engine Heat can cause firePrincipal Safety Standards EMF InformationRadiation can cause interference ARC Welding can cause interferenceSignification des symboles Consignes DE SÉ Curité Lire Avant UtilisationUN Choc É Lectrique peut tuer LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES PIÈ CES Chaudes peuvent provoquer des brû lures graves LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent provoquer des blessures ’EXPLOSION DE LA Batterie peutLA Chaleur DU Moteur peut pro- voquer un incendie LA Chute DE L’APPAREIL peut blesserPrincipales normes de sé curité Information sur les champs é lectromagné tiquesLE Soudage À L’ARC risque de provoquer des interfé rences Consignes relatives aux stimulateurs cardiaquesSymbols And Definitions DefinitionsDimensions, Weights, And Operating Angles SpecificationsWeld, Power, And Engine Specifications Warranty Minutes Welding Minutes Resting Fuel ConsumptionDuty Cycle And Overheating 40% Duty Cycle At 400 AmperesAC Auxiliary Power Volt-Ampere CurvesOptional AC Power Plant Curves Installing Muffler Pipe InstallationInstalling Welding Generator Activating The Dry Charge Battery Do not overfill battery cellsVent Caps For 12 MinutesConnecting The Battery Engine Prestart ChecksConnect Negative Cable Last FullPut cap on fitting when cylinder is removed Installing Ether Cylinder Optional Ether Starting AidConnecting To Weld Output Terminals 10 100% Duty Cycle Selecting Weld Cable Sizes100 ft 30 m Or Less OM-130 098 Operating the Welding Generator Controls See SectionDescription Of Front Panel Controls See Section Remote A/V ControlOperating Auxiliary Equipment Volt And 240 Volt Duplex ReceptaclesAustralian, British, And South African Receptacle Options Optional Auxiliary Power ReceptaclesGfci Receptacle Option Connecting Optional Auxiliary Power Plant Maintenance and Troubleshooting Maintenance Label Servicing Air Cleaner To clean air filterStop engine HoseTo replace primary fuel filter Servicing Fuel And Lubrication SystemsTo change oil and filter Models With Automatic Idle Optional Adjusting Engine SpeedStandard Models Overload Protection Servicing Optional Ether Starting Aid Full EmptyWelding Inspecting And Cleaning Optional Spark ArrestorTroubleshooting Auxiliary Power Check connections to auxiliary power plant see SectionEngine Maximum see SectionElectrical Diagram Circuit Diagram For Welding GeneratorRUN-IN Procedure WetstackingRun-In Procedure Using Load Bank Stop engine Do not touch hot exhaustBank/grid From flammablesRun-In Procedure Using Resistance Grid Grounding Generator To Truck Or Trailer Frame Auxiliary Power GuidelinesSelecting Equipment Grounding When Supplying Building Systems How Much Power Does Equipment Require?Earth ground if supplying Amperes x Volts = WattsApproximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsPower Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP xPower Company Service Obtain and install correct switchSafety practices 120 Single-PhaseSelecting Extension Cord Use Shortest Cord Possible Current Load Watts AmperesParts List 118 117 116 11571Includes 113 114 11065 FIG Dia Part Description Quantity Mkgs 126 102 Optional Equipment Panel, Front w/Components Panel, Front w/Components -1 Item Generator 11 10Generator -1 Item 114 IncludesService SupportCall Contact your Distributor forHobart Welding Products

3225DX specifications

The Hobart 3225DX is a robust and versatile commercial dishwasher designed to meet the needs of restaurants, catering services, and institutions requiring efficient dishwashing solutions. Engineered for high performance, this machine combines advanced technology with user-friendly features to deliver exceptional cleaning results.

One of the standout features of the Hobart 3225DX is its high capacity. It can wash up to 60 racks per hour, making it suitable for busy kitchens. The machine is designed to handle a wide variety of dishware, glassware, and utensils, ensuring a thorough clean for all types of kitchenware.

Equipped with a powerful two-speed wash pump, the Hobart 3225DX guarantees optimal cleaning efficiency. Users can choose between a standard wash cycle for regular soiled items and a more intense cycle for heavily soiled dishware. This flexibility allows kitchen staff to adjust the machine's performance based on their specific needs.

The dishwasher features an advanced filtration system that minimizes the need for frequent cleaning of the internal components. This system captures food particles and debris, enhancing the machine's longevity and maintaining consistently clean results. Additionally, the Hobart 3225DX is designed with a built-in booster heater that increases water temperature to ensure optimal sanitization, complying with health and safety standards.

User convenience is a key consideration in the design of the Hobart 3225DX. The intuitive controls and clear display make operation straightforward, even for first-time users. The machine is also engineered for easy maintenance, with accessible components that allow for quick service and troubleshooting.

Another notable characteristic is its energy efficiency. The Hobart 3225DX is designed to minimize water and energy consumption without compromising performance. This aligns with the growing emphasis on sustainability in the foodservice industry, offering an eco-friendly solution that helps businesses reduce operational costs.

In summary, the Hobart 3225DX is an efficient, high-capacity commercial dishwasher that combines powerful cleaning capabilities with user-friendly features. Its advanced wash pump, effective filtration system, and energy-efficient design make it an ideal choice for any busy kitchen looking to streamline dishwashing operations and maintain the highest hygiene standards.
Top Page Image Contents