Hobart Welding Products 210 597J Operating Auxiliary Equipment, Generator Power Panel Receptacles

Page 27

SECTION 7 − OPERATING AUXILIARY EQUIPMENT

.The welding generator provides power while welding and with the Amperage control in any position. However, under these conditions equipment connected to the welding generator may be subject to larger than normal voltage fluctuations. It is recommended that only lamps be powered under these conditions.

7-1. Generator Power Panel Receptacles

 

 

 

 

 

3

 

 

 

 

 

2

1

! Use GFCI-protected extension cord.

.Generator power decreases as weld current increases.

Set Amperage control at max. for full generator power.

1240 V 20 A AC Duplex Receptacle RC1

RC1 supplies 60 Hz single-phase power at weld/power speed. Maximum output is 4 kVA/kW.

2120 V 20 A AC Duplex Receptacle RC2

RC2 supplies 60 Hz single-phase power at weld/power speed. Maximum output from RC2 is 2.4 kVA/kW.

3 Supplementary Protector CB1

CB1 protects the receptacles from over- load. If CB1 opens, the receptacles do not work.

226 005

.Place switch in the On position to re- set. If supplementary protector contin- ues to open, contact Factory Authorized Service Agent.

Combined output of all receptacles limited to 4 kVA/kW rating of the generator (See Section 11 − Generator Power Guide- lines).

EXAMPLE: If 15 A is drawn from the 120 volt duplex receptacle, only 9 A is available from the 240 V duplex receptacle.

(120 V x 15 A) + (240 V x 9 A) = 4 kVA/KW.

OM-4418 Page 23

Image 27
Contents OM-4418 ProcessesDescription From Hobart to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion Fumes and Gases can be hazardousBuildup of GAS can injure or kill ARC Rays can burn eyes and skinCompressed Air Hazards Engine HazardsFalling Unit can cause injury Welding Wire can cause injuryHOT Parts can cause burns and injury Fire or Explosion hazardRadiation can cause interference Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationDoivent être confiés qu’à des personnes qualifiées Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UN Choc Électrique peut tuerDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut affecter l’ouïe ’EXPLOSION DE LA Batterie peuDES Organes Mobiles peuvent pro voquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessuresRisque D’INCENDIE OU D’EXPLO- Sion ’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électriqueDES Organes Mobiles peuvent provoquer des blessures LES Fils DE Soudage peuvent provoquer des blessuresProposition californienne 65 Avertissements Principales normes de sécuritéInformation EMF − Definitions − SpecificationsSymbol Definitions Weld, Power, And Engine SpecificationsWeld Amps At Rated Duty Cycle Dimensions, Weights, And Operating AnglesAux Power Gal./Hr Weld Power In KW Fuel ConsumptionDuty Cycle Generator Power CurvePower AC Power AmperesVolt-Ampere Curves Volts Max Amp Min AmpAC Amps Location − InstallationInstalling Welding Generator MovementGrounding Generator When Supplying Building Systems Engine Prestart ChecksOil Connecting To Weld Output Terminals Weld cable terminal and copper bar Correct InstallationTools Needed 350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Connecting to weldSelecting Weld Cable Sizes 150 ft 200 ft 250 ftMaterial Thickness Reference Chart Controls See Section − Operating the Welding GeneratorTo Start To Stop turn engine switch to OffDescription Of Controls See Section Amperage Selection Table For Stick Smaw ElectrodesX 15 a + 240 V x 9 a = 4 kVA/KW OM-4418 Generator Power Panel Receptacles− Operating Auxiliary Equipment Use GFCI-protected extension cordRoutine Maintenance − MaintenanceStop engine Servicing Air CleanerWelding − TroubleshootingTroubleshooting Generator PowerWith proper viscosity oil for operating temperature EngineStarting difficult Circuit Diagram For Welding Generator − Electrical Diagrams− Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame How Much Power Does Equipment Require? Grounding When Supplying Building SystemsFarm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Industrial Motors Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentKVA/HP x HP x 1000 / Volts = Starting Amperage Power Required To Start MotorHow Much Power Can Generator Supply? Single-Phase Induction Motor Starting RequirementsTypical Connections To Supply Standby Power Cord Lengths for 240 Volt Loads Selecting Extension Cord Use Shortest Cord PossibleCord Lengths for 120 Volt Loads Current Load Watts Amperes− Stick Welding Smaw Guidelines Stick Welding ProcedureElectrode and Amperage Selection Chart Striking an Arc − Scratch Start TechniqueStriking an Arc − Tapping Technique 10-30 9090 End View of Work Angle Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Positioning Electrode HolderElectrode Movement During Welding Conditions That Affect Weld Bead Shape16 in 1.6 mm Tack Welds Butt JointsLap Joint Tee JointPossible Causes Corrective Actions Troubleshooting − PorosityTroubleshooting − Excessive Spatter Weld TestTroubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Excessive Penetration Troubleshooting − Burn-Through Troubleshooting − Waviness Of BeadTroubleshooting − Distortion Work like a Pro Main Assembly − Parts ListSR1 Service SupportAssistance Hobart Welding Products Contact your Distributor for

210 597J, OM-4418 specifications

The Hobart Welding Products OM-4418,210 597J is a premium multi-process welder designed to meet the diverse needs of both professional and hobbyist welders. Renowned for its reliability and ease of use, this machine embodies the essence of Hobart's commitment to quality and performance in the welding industry.

One of the standout features of the OM-4418,210 597J is its versatility. This unit supports MIG, TIG, and Stick welding processes, allowing users to seamlessly switch between methods depending on the task at hand. The machine is equipped with a powerful inverter technology that enhances its efficiency and power output while reducing energy consumption. This means you can achieve high-quality welds with less impact on your electricity bill.

Another notable characteristic is its user-friendly interface. The welder features an intuitive control panel that allows for easy adjustments, enabling users to set the voltage and wire feed speed with precision. The digital display provides clear readouts of the current settings, making it easier for welders to monitor their work and make adjustments on the fly.

Safety is a critical concern in welding, and the OM-4418,210 597J incorporates several safety features to protect the operator. It is designed with built-in thermal overload protection, which prevents the machine from overheating during extended use. Additionally, the welder is equipped with a robust and durable housing that can withstand the rigors of a workshop environment.

The portability of the OM-4418,210 597J is another advantage, as it is lightweight and comes with a comfortable carrying handle. This enables users to transport it easily to job sites or move it around the workshop without strain. The unit is also compatible with standard household power outlets, adding to its convenience for both home and professional use.

In terms of build quality, the Hobart OM-4418,210 597J is designed to deliver consistent performance. It supports a wide range of welding materials, including steel, stainless steel, and aluminum, giving users the flexibility to tackle various projects. With a duty cycle that meets the demanding requirements of industrial applications, this welder ensures minimal downtime in production.

Overall, the Hobart Welding Products OM-4418,210 597J stands out as an exceptional choice for welders seeking a reliable, versatile, and user-friendly multi-process welding machine. With its advanced technologies and robust features, it promises to deliver excellent performance and lasting results across a wide range of welding applications.