Hobart Welding Products 210 manual Replacing Switch And/Or Head Tube

Page 29

7-7. Replacing Switch And/Or Head Tube

Y Turn Off welding power source /wire feeder and disconnect gun.

1 Remove handle locking nut.

3 Slide handle.

2 Remove switch housing. Install new switch and connect leads (polarity is not important). Reassemble in reverse order. If replacing head tube, continue to end of figure.

4Secure head tube in vice.

5Loosen jam nut. Remove from vice and turn head tube out by hand.

6 Hand-tighten head tube into cable connector.

7Place head tube in vice and tighten until nuts are tight.

8Remove from vice. Reposition handle and install switch housing. Secure with handle locking nut.

Tools Needed:

19 mm	Ref. ST-800 795-C

OM-227 978 Page 25

Image 29

Contents Processes OM-227 978ADescription 2006−12From Hobart to You Table of Contents − Parts List Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéSymbols And Definitions − SpecificationsSpecifications − DefinitionsVolt-Ampere Curves Duty Cycle And OverheatingAmperes OutputInstalling Work Clamp − InstallationInstalling Welding Gun Changing Polarity Process/Polarity TableInstalling Gas Supply First, and never to a line ter- minal Selecting a Location And Connecting Input PowerDo not move or operate unit where it could tip Installing Wire Spool And Adjusting Hub Tension Electrical Service GuideFlux Nozzle Installing Contact Tip And NozzleAppropriate setting Connecting Optional Spool GunHold wire tightly to keep it from unraveling Threading Welding WireControls − OperationWeld Parameter Chart For 230 VAC Model 227 949-A Routine Maintenance − Maintenance &TROUBLESHOOTINGOverload Protection Drive Motor ProtectionReplacing Gun Contact Tip Changing Drive Roll Or Wire Inlet GuideTurn Off power before replacing contact tip To Reassemble Gun Cleaning Or Replacing Gun LinerDisconnect gun from unit Replacing Switch And/Or Head Tube Does not run Troubleshooting TableTrouble Remedy OM-227 978 Circuit Diagram − Electrical Diagram227 951-A Typical MIG Process Connections − MIG Welding Gmaw GuidelinesWire Size Amperage Range Typical MIG Process Control SettingsThickness to Amperage a AmperageHolding And Positioning Welding Gun Conditions That Affect Weld Bead Shape Cored wireGun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Troubleshooting − Porosity Troubleshooting − Excessive SpatterTroubleshooting − Excessive Penetration Possible Causes Corrective ActionsTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Distortion Troubleshooting − Waviness Of BeadCommon MIG Shielding Gases ApplicationWire does not feed Troubleshooting Guide For Semiautomatic Welding EquipmentOM-227 978 Main Assembly − Parts ListDia Part Description Quantity Dia Part Description Quantity Mkgs 231 H-14 GunConsumables Optional Drive RollsOptions Page Work like a Pro Assistance ServiceSupport Hobart Welding Products Contact your Distributor for

Related manuals

Manual 56 pages 12.21 Kb