Woodstock M1049 manual JIM@ D8@EKE8E FGI8K@FEJ JKLG G8IKJ

Page 4

<C<:KI@:8C J8=<KP @EKIF;L:K@FE

J<IM@:< D8@EK<E8E:< FG<I8K@FEJ J<KLG

G8IKJ

Setting RPM	30
RPM Chart	31
Setting Power Feed Rate	32
Threading Setup	33
MAINTENANCE	34
General Maintenance	34
General Cleaning	34
General Lubrication	34
SERVICE	36
Cross Slide Backlash	36
Cross-Slide and Saddle-Gib Adjustments	36
Replacing the V-Belt	37
Replacing the Cogged-Belt	37
Electrical Safety Instructions	38
Wiring Diagram	39
Troubleshooting	40
PARTS	43
Drive Belt	43
Belt Tensioner	44
Change Gears	45
Headstock	46
Quick-Change Gearbox	47
Apron	48
Saddle & Cross Slide	50
Compound Rest & Tool Post	51
Tailstock	52
Steady Rest	53
Follow Rest	53
Bed	54
Electrical & Tools	55
Machine Labels	56
WARRANTY	61

LJ<K?<HL@:B>L@;<G8><C89<CJKFJ<8I:?FLK@E=FID8K@FE=8JK

Image 4

Contents 7C8=IDEA6I= Page Table of Contents JIM@ D8@EKE8E FGI8K@FEJ JKLG G8IKJ Introduction Woodstock Technical Support@EKIFLK@FE @EKIFLK@FE @EKIFLK@FE Controls and Features Safety For Your Own Safety Read Manual Before Operating MachineJ8=KP Additional Safety Instructions for Lathes Avoiding Potential Injuries Electrical Circuit RequirementsAmps NemaExtension Cords Grounding Requirements50 ft Setup Installed Accessories Figure QtyPackaged Accessories Figure InventoryMachine Placement Cleaning MachineUncrating & Lifting JKLGTo begin the test run procedure, do these steps Test Run and Break-InLathe Operations GeneralDisconnect Power to the Lathe Chuck and Faceplate MountingReplacing Jaws To remove a set of jaws, do these stepsTo install the four-jaw chuck, do these steps Using the Four-Jaw ChuckTo load a workpiece in the four-jaw chuck, do these steps Using the Faceplate To install the faceplate, do these stepsUsing the Tailstock To use the tailstock, do these stepsTailstock Alignment To setup the tailstock to cut tapers, do these stepsTo align the tailstock, do these steps =`li\22% Tailstock adjustment option #2 Using Centers Using the Follow Rest Using the Steady RestTo use the steady rest, do these steps Using the Tool Posts Setting Compound SlideTo set the angular position, do these steps Using Manual Feed Longitudinal HandwheelTo determine and set the needed cutting RPM, do these steps Setting RPMCutting Speeds for High Speed Steel HSS Cutting Tools RPM Chart Setting Power Feed Rate To set and engage the power feed, do these stepsThreading Setup To setup for threading, do these stepsMaintenance General MaintenanceGeneral Cleaning General Lubrication=`li\43%End-cap bushing and tailstock Ball oilers Cross-Slide and Saddle Gib Adjustments ServiceCross Slide Backlash Replacing the V-Belt Replacing the Cogged BeltTo replace the V-belt, do these steps To replace the cogged-belt, do these stepsElectrical Safety Instructions HL8C@=@CKI@@8E% Due toWiring Diagram StopTroubleshooting Motor & ElectricalOperation and Work Results +09\eZkfgCXk\D%J`eZ\/&0 Parts Drive BeltBelt Tensioner Change Gears Headstock Quick-Change Gearbox Apron Front ViewApron Parts List Saddle & Cross Slide Compound Rest & Tool Post Tailstock Steady Rest Follow RestBed Electrical & Tools XPS09MMachine Labels Grouped Warnings LabelPage Page Page Place Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah