Woodstock M1049 manual Chuck and Faceplate Mounting, Disconnect Power to the Lathe

Page 21

D('+09\eZ_kfgCXk_\D]^%J`eZ\/&'0

Chuck and Faceplate

Mounting

The three-jaw scroll chuck has hardened steel jaws that self-center the workpiece. An extra set of jaws is included for machining larger workpieces.

The four-jaw chuck also has hardened steel jaws but are adjusted independently to hold an off-center workpiece. Each jaw can be removed from the chuck body and reversed for special clamping applications.

The cast-iron faceplate has slots for T-bolts that hold clamping fixtures. This face plate and aftermarket clamping hardware will hold non-cylindrical parts such as castings for many types of turning operations.

Both chucks and the faceplate are removed and installed the same way.

To remove and install the chuck or face plate, do these steps:

1.DISCONNECT POWER TO THE LATHE!

2.Lay a piece of plywood over the bedways to protect the precision-ground bedways.

3.Use a 2mm hex wrench and loosen the two chuck retaining set screws shown in Figure 11.

4. Use spindle and chuck levers to loosen the chuck from the spindle as shown in Figure 12.

Note: The chuck and spindle are right-hand thread.

5. Support the chuck, and while anticipating its weight, unscrew the chuck counterclockwise and set it aside.

6. Clean the threads on the spindle and the new chuck or faceplate with a clean rag and oil the threads.

7. Thread the chuck or faceplate onto the spindle and tighten in place with the levers.

8. Tighten the two setscrews.

G@E:??8Q8I;Gifk\Zkpfli_Xe[jXe[ gi\Z`j`fe ^ifle[ Y\[nXpj n`k_ gcp$ nff[ n_\e i\dfm`e^ Y\eZ_kfg cXk_\ Z_lZb K_\ _\Xmp n\`^_k f] X ]Xcc$ `e^ Z_lZb ZXe ZXlj\ j\i`flj `ealip%

Set Screw

=`^li\11%Chuck retaining setscrew.

Spindle Lever

Chuck

Lever

Push

Pull

FG<I8K@FEJ

=`^li\12%Chuck removal levers.

-19-

Image 21

Contents 7C8=IDEA6I= Page Table of Contents JIM@ D8@EKE8E FGI8K@FEJ JKLG G8IKJ Woodstock Technical Support Introduction@EKIFLK@FE @EKIFLK@FE @EKIFLK@FE Controls and Features For Your Own Safety Read Manual Before Operating Machine SafetyJ8=KP Additional Safety Instructions for Lathes Avoiding Potential Injuries Circuit Requirements ElectricalAmps NemaGrounding Requirements Extension Cords50 ft Installed Accessories Figure Qty SetupPackaged Accessories Figure InventoryCleaning Machine Machine PlacementJKLG Uncrating & LiftingTest Run and Break-In To begin the test run procedure, do these stepsGeneral Lathe OperationsChuck and Faceplate Mounting Disconnect Power to the LatheTo remove a set of jaws, do these steps Replacing JawsUsing the Four-Jaw Chuck To install the four-jaw chuck, do these stepsTo load a workpiece in the four-jaw chuck, do these steps To install the faceplate, do these steps Using the FaceplateTo use the tailstock, do these steps Using the TailstockTo setup the tailstock to cut tapers, do these steps Tailstock AlignmentTo align the tailstock, do these steps =`li\22% Tailstock adjustment option #2 Using Centers Using the Steady Rest Using the Follow RestTo use the steady rest, do these steps Setting Compound Slide Using the Tool PostsTo set the angular position, do these steps Longitudinal Handwheel Using Manual FeedSetting RPM To determine and set the needed cutting RPM, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools RPM Chart To set and engage the power feed, do these steps Setting Power Feed RateTo setup for threading, do these steps Threading SetupGeneral Maintenance MaintenanceGeneral Cleaning General Lubrication=`li\43%End-cap bushing and tailstock Ball oilers Service Cross-Slide and Saddle Gib AdjustmentsCross Slide Backlash Replacing the Cogged Belt Replacing the V-BeltTo replace the V-belt, do these steps To replace the cogged-belt, do these steps HL8C@=@CKI@@8E% Due to Electrical Safety InstructionsStop Wiring DiagramMotor & Electrical TroubleshootingOperation and Work Results +09\eZkfgCXk\D%J`eZ\/&0 Drive Belt PartsBelt Tensioner Change Gears Headstock Quick-Change Gearbox Front View ApronApron Parts List Saddle & Cross Slide Compound Rest & Tool Post Tailstock Follow Rest Steady RestBed XPS09M Electrical & ToolsGrouped Warnings Label Machine LabelsPage Page Page Place Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah