Grizzly G4002, G4003 instruction manual Machine Data

Page 32

MACHINE DATA

SHEET

Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

GRIZZLY MODEL G4002 12" X 24" GEAR HEAD LATHE

Design Type	Floor Model
Overall Dimensions:
Overall Length	53"
Overall Width	26"
Height With Optional Stand	521⁄2"
Height Without Optional Stand	23"
Bed Width	71⁄4"
Spindle Bore	17⁄16''
Spindle Taper	#5 Morse Taper
Tailstock Taper	#3 Morse Taper
Tailstock Barrel Diameter	19⁄16''
Weight (Net)	913 lbs.
Weight (Shipping)	1015 lbs.
Crate Size	59" L x 30" W x 29" H
Footprint	53" x 23"
Construction:	Cast Iron
Capacity:
Swing Over Bed	12''
Swing Over Gap	17''
Swing Over Cross Slide	7''
Distance Between Centers	24''
Spindle	D1-4 Cam Lock
Compound Travel	31⁄4''
Cross Slide Travel	61⁄4''
Tailstock Barrel Travel	4''
Spindle Speeds	70, 200, 220, 270, 360, 600, 800, 1000, 1400 RPM
Feed Rate Range	40 @ .0011'' - .031''
Thread Range Inch	40 @ 4 TPI - 112 TPI
Thread Range Metric	29 @ .2 - 4.5 mm
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	11⁄2
Phase ⁄ Hertz	Single Phase ⁄ 60Hz
Voltage	220V
Amps	9
RPM	1725
Bearings	Shielded And Lubricated For Life
Features:
........................................................................	6'' 3-Jaw Chuck With Two Set Of Jaws
..........................................................................	8'' 4-Jaw Chuck With Reversible Jaws
............................................................	Quick Change Tool Post With One Tool Holder
..........................................................................................................	Extra Tool Holder
..................................................................................................................	Steady Rest
....................................................................................................................	Follow Rest
..............................................................................................................	10'' Face Plate
....................................................................	1⁄2'' Drill Chuck W⁄ # 3 Morse Taper Arbor
..................................................	2- #3 Morse Taper Dead Centers (1 Carbide Tipped)
..........................................................................................	#3 Morse Taper Live Center
..................................................................................................	Set of 6 Change Gears
........................................................................................................................	Tool Box

Specifications, while deemed accurate, are not guaranteed.

-30-	G4002/3 Gear Head Lathes

Image 32

Contents Gear Head Metal Lathe Model G4002 / G4003Page Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For The Lathe Extension Cords Circuit Requirements220V Operation Grounding Introduction CommentaryUnpacking Piece InventoryClean Up Site Considerations Lubrication Assembly & SetupMountingChucks If the chuck is still tight on the spindle To install a chuckTo remove a chuck Live Center Steady Rest See FigureFollow Rest Jaw ChuckControls Spindle SpeedsNever change speeds while spindle or motor is in motion ExampleFeed Direction Never move selection levers while machine is runningFeed Rate Chart Feed rate selectionThread Selection Inch thread selectionExample To use the chart Metric thread selectionGear Placement G4002/3 Gear Head Lathes To change gearsCarriage Controls Tool Post and Holder Tailstock Controls Detail of tailstock controls G4002/3 Gear Head LathesTest Run Before starting the machineAdjustments GibsSteady/Follow Rest This bolt locks the apron in placeTailstock TIPTailstock offset adjustment screw G4002/3 Gear Head Lathes Maintenance Bearing Preload Closure Machine Data Grizzly Model G4003 12 X 36 Gear Head Lathe Electrical Components Start Button G4002/3 Gear Head Lathes Screw Eccentric Shaft PSB26M CAP Screw M6-1 X G4002/3 Gear Head Lathes Lead Screw G4002/3 Gear Head Lathes Hand Wheel G4002/3 Gear Head Lathes Saddle Compound Slide G4002/3 Gear Head Lathes Center Motor 2 HP OIL CAP Lathe BED Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC