Grizzly G4002 instruction manual Grizzly Model G4003 12 X 36 Gear Head Lathe

Page 33

MACHINE DATA

SHEET

Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

GRIZZLY MODEL G4003 12" X 36" GEAR HEAD LATHE

Design Type	Floor Model
Overall Dimensions:
Overall Length	61"
Overall Width	23"
Height With Optional Stand	541⁄2"
Height W⁄O Optional Stand	23"
Bed Width	71⁄4"
Spindle Bore	17⁄16''
Spindle Taper	#5 Morse Taper
Tailstock Taper	#3 Morse Taper
Weight (Net)	917 lbs.
Weight (Shipping)	1040 lbs.
Crate Size	66" L x 30" W x 28" H
Footprint	61" x 23"
Construction:	Cast Iron
Capacity:
Swing Over Bed	12''
Swing Over Gap	17''
Swing Over Cross Slide	7''
Distance Between Centers	36''
Spindle	D1-4 Cam Lock
Compound Travel	31⁄4''
Cross Slide Travel	61⁄4''
Tailstock Barrel Travel	4''
Spindle Speeds	70, 200, 220, 270, 360, 600, 800, 1000, 1400 RPM
Feed Rate Range	40 @ .0011'' - .031''
Thread Range Inch	40 @ 4 TPI - 112 TPI
Thread Range Metric	29 @ .2 - 4.5 mm
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	11⁄2
Phase ⁄ Hertz	Single Phase ⁄ 60Hz
Voltage	220V
Amps	9
RPM	1725
Bearings	Shielded And Lubricated For Life
Features:
......................................................................	6'' 3-Jaw Chuck With Two Sets Of Jaws
..........................................................................	8'' 4-Jaw Chuck With Reversible Jaws
............................................................	Quick Change Tool Post With One Tool Holder
..........................................................................................................	Extra Tool Holder
..................................................................................................................	Steady Rest
....................................................................................................................	Follow Rest
..............................................................................................................	10'' Face Plate
......................................................................	1/2'' Drill Chuck W/ #3 Morse Taper Arbor
................................................2-	#3 Morse Taper Dead Centers (1 Carbide Tipped)
........................................................................................	#3 Morse Taper Live Center
..........................................................................................................................	Oil Can
..............................................................................................	Set Of Six Change Gears
........................................................................................................................	Tool Box

Specifications, while deemed accurate, are not guaranteed.

G4002/3 Gear Head Lathes

-31-

Image 33

Contents

Model G4002 / G4003 Gear Head Metal LathePage Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Additional Safety Instructions For The Lathe Circuit Requirements 220V Operation GroundingExtension Cords Commentary IntroductionPiece Inventory UnpackingClean Up Site Considerations Assembly & Setup MountingChucksLubrication To install a chuck To remove a chuckIf the chuck is still tight on the spindle See Figure Live Center Steady RestJaw Chuck Follow RestSpindle Speeds ControlsNever change speeds while spindle or motor is in motion ExampleNever move selection levers while machine is running Feed DirectionFeed rate selection Feed Rate ChartInch thread selection Thread SelectionExample Metric thread selection To use the chartTo change gears Gear Placement G4002/3 Gear Head LathesCarriage Controls Detail of tailstock controls G4002/3 Gear Head Lathes Tool Post and Holder Tailstock ControlsBefore starting the machine Test RunGibs AdjustmentsThis bolt locks the apron in place Steady/Follow RestTIP TailstockTailstock offset adjustment screw G4002/3 Gear Head Lathes Maintenance Bearing Preload Closure Machine Data Grizzly Model G4003 12 X 36 Gear Head Lathe Electrical Components Start Button G4002/3 Gear Head Lathes Screw Eccentric Shaft PSB26M CAP Screw M6-1 X G4002/3 Gear Head Lathes Lead Screw G4002/3 Gear Head Lathes Hand Wheel G4002/3 Gear Head Lathes Saddle Compound Slide G4002/3 Gear Head Lathes Center Motor 2 HP OIL CAP Lathe BED Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC

Related manuals

Manual 54 pages 5.54 Kb